Follow-ups left open by the 8852C ACK responder review (#489)
I maintainer di solito rispondono entro 1 giorno
Nessuno ha ancora preso questa issue.
Valutazione
- Difficoltà
- 5/5
- Tempo stimato
- Più di una settimana
- Idoneità per principianti
- 6/100
- Tipo di issue
- Bug
- Chiarezza
- Da chiarire
- Stato di attività
- Attiva
- Stack tecnologico
- c
- Ambito
- embedded-iot, networking
Direzione di ricerca
Start with the #489 review thread, since most measurements are excluded there. Item 3 is the most contained entry point: HalKestrel::coex_mac_init sets ENBT only for the 8852B, so the 8852C path needs a fix. Item 1 depends on hardware bench work with a firmware RAM dump and a vendor A/B, and AdapterCaps.h holds the matrix to update. Done means a root cause or a reproducible fix for the dead-ACK sessions, not a guess.
Scritto dal modello di indicizzazione a partire dal testo della issue.
Descrizione
Left open by the review and bisect of #489 (8852C hardware ACK responder). Bench: TX50UH (RTL8832CU) x2, 8812CU soliciting with CCX tx.report, near field.
1. 8852C bring-ups that never answer an ACK: cause unknown
The responder arms, the entry reads back, injection works, and the chip answers no ACK for the whole session. Measured rate on this bench: ~1/3 of soft re-runs in the morning, ~85% by the afternoon, on ch161 and ch6, on both units; one 8852B-side report of ~1 in 55 from the author.
Excluded by measurement (details in the #489 review thread):
- temperature (meter flat; dead at the coldest reading after 120 s VBUS-offs) and retained chip state (120 s VBUS cuts);
- the TX chain (99% of host-injected frames witnessed in a dead session) and the soliciting side (an independent witness sees the ACKs vanish);
- every host-readable register and SRAM read at the correct 0x20 stride: ADDR_CAM, BSSID CAM, DMAC/CMAC tables (uninitialised in RX-only sessions, no separating bit), MAC 0x8000/0xC000/0xD800 blocks, BB 0x10000-0x17FFF, RF path 0/1, GNT;
- levers: host-written minimal and vendor-default CMAC entries, the CMAC H2C, forced WiFi-only GNT with and without the vendor coex init, a host-written BSSID CAM entry, the CAM slot.
The one lead: R_AX_WMAC_TX_INFO0_DEBUG (0xCAE8) reads 0x10914012 in every dead session and 0x10915012 in good ones (bit 12), so the TMAC does issue the response, and the RF path-0 TX registers show it never reaches the RF. Next experiments: a firmware RAM dump dead vs good, and a vendor rtl8852cu A/B on the same unit with a real station answering, to learn whether the vendor bring-up ever shows the state at all.
2. Kestrel host injection on ch161 nearly silent
Both TX50UH units, txdemo TX-only at 6M, 20 ms gap, ch161: 6-10 of ~290 frames witnessed, by either an 8852C or the 8812CU, in good and dead ACK sessions alike. Same setup on ch6: 97-99%. Earlier 8852C -> 8812CU injection A/Bs (~97%) were on ch6. Needs a 5 GHz injection A/B against the vendor driver on this unit before any 5 GHz Kestrel TX number is trusted.
3. 8852C coex init on the C die is a no-op
HalKestrel::coex_mac_init sets ENBT for the 8852B only, so on the 8852C both write_lte calls time out ("Kestrel coex: LTE interface not ready" twice per session) and the GNT stance is skipped. The vendor's 8852C path (coex_8852c.c) does not use the LTE window (mac_write_lte_8852c returns MACNOTSUP); it writes R_AX_GNT_SW_CTRL and R_AX_BTC_CFG / R_AX_BT_CNT_CFG / R_AX_CCA_CFG_0 directly. Cold state read on this unit: GNT_SW_CTRL 0x175775, GNT_VAL 0x118 (BT granted, WL not), BTC_CFG bit 31 clear. Forcing the WiFi-only grant did not change item 1, so this is a correctness cleanup, not a fix.
4. Bench note
The dead rate in item 1 rose through a day of back-to-back sessions on both units and no power cycle reset it. Anyone measuring the 8852C responder late in a session day will see a different rate from the morning; the matrix in AdapterCaps.h should say when in the day its rows were taken.
- Lingua principale
- C
- Stelle
- 56
- Fork
- 29
- Merge medio
- 3h 43m
- PR unite (30g)
- 75
Preparare l'ambiente
Questo progetto non fornisce container di sviluppo, Dockerfile né guida per i contributori, quindi l'ambiente è a tuo carico: parti dal suo README e consulta la nostra guida al primo contributo per i passaggi generali.
Come iniziare
- Leggi tutta la issue e poi la guida ai contributi del progetto.
- Commenta sulla issue per dire che te ne occupi tu — evita che due persone facciano lo stesso lavoro.
- Fai un fork del repository e lavora su un branch.
- Apri una pull request che faccia riferimento al numero della issue.
Altre issue di OpenIPC/devourer
-
Difficoltà 2/5 1-3 ore Idoneità per principianti 82/100
I maintainer di solito rispondono entro 1 giorno
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Forse già presa @josephnef l’ha presa oggi. Apertaenhancement
Difficoltà 4/5 3-5 giorni Idoneità per principianti 42/100
I maintainer di solito rispondono entro 1 giorno
-
Difficoltà 5/5 Più di una settimana Idoneità per principianti 12/100
OpenIPC/devourer#579 · 1 commento ·
I maintainer di solito rispondono entro 1 giorno
-
enhancement
Difficoltà 5/5 Più di una settimana Idoneità per principianti 12/100
I maintainer di solito rispondono entro 1 giorno
-
enhancement
Difficoltà 5/5 Più di una settimana Idoneità per principianti 8/100
I maintainer di solito rispondono entro 1 giorno
Tutte le issue di OpenIPC/devourer
Issue simili
-
Difficoltà 2/5 1-3 ore Idoneità per principianti 72/100
I maintainer di solito rispondono entro 1 giorno
-
Needs-Triage
Difficoltà 2/5 1-3 ore Idoneità per principianti 66/100
I maintainer di solito rispondono entro 2 giorni
-
issue: bug report
Difficoltà 2/5 1-3 ore Idoneità per principianti 82/100
I maintainer di solito rispondono entro 2 giorni
-
cross-platform fix-now
Difficoltà 2/5 1-3 ore Idoneità per principianti 76/100
I maintainer di solito rispondono entro 1 giorno
-
feature:index kind:crash status:confirmed triaged
Difficoltà 2/5 1-3 ore Idoneità per principianti 77/100
clice-io/clice#1123 · 1 commento ·
I maintainer di solito rispondono entro 1 giorno