Follow-ups left open by the 8852C ACK responder review (#489)
Les mainteneurs répondent en général sous 1 jour
Personne n'a encore pris cette issue.
Évaluation
- Difficulté
- 5/5
- Temps estimé
- Plus d'une semaine
- Accessibilité débutants
- 6/100
- Type d'issue
- Bug
- Clarté
- À clarifier
- Activité
- Active
- Stack technique
- c
- Domaine
- embedded-iot, networking
Piste de recherche
Start with the #489 review thread, since most measurements are excluded there. Item 3 is the most contained entry point: HalKestrel::coex_mac_init sets ENBT only for the 8852B, so the 8852C path needs a fix. Item 1 depends on hardware bench work with a firmware RAM dump and a vendor A/B, and AdapterCaps.h holds the matrix to update. Done means a root cause or a reproducible fix for the dead-ACK sessions, not a guess.
Rédigé par le modèle d'indexation à partir du texte de l'issue.
Description
Left open by the review and bisect of #489 (8852C hardware ACK responder). Bench: TX50UH (RTL8832CU) x2, 8812CU soliciting with CCX tx.report, near field.
1. 8852C bring-ups that never answer an ACK: cause unknown
The responder arms, the entry reads back, injection works, and the chip answers no ACK for the whole session. Measured rate on this bench: ~1/3 of soft re-runs in the morning, ~85% by the afternoon, on ch161 and ch6, on both units; one 8852B-side report of ~1 in 55 from the author.
Excluded by measurement (details in the #489 review thread):
- temperature (meter flat; dead at the coldest reading after 120 s VBUS-offs) and retained chip state (120 s VBUS cuts);
- the TX chain (99% of host-injected frames witnessed in a dead session) and the soliciting side (an independent witness sees the ACKs vanish);
- every host-readable register and SRAM read at the correct 0x20 stride: ADDR_CAM, BSSID CAM, DMAC/CMAC tables (uninitialised in RX-only sessions, no separating bit), MAC 0x8000/0xC000/0xD800 blocks, BB 0x10000-0x17FFF, RF path 0/1, GNT;
- levers: host-written minimal and vendor-default CMAC entries, the CMAC H2C, forced WiFi-only GNT with and without the vendor coex init, a host-written BSSID CAM entry, the CAM slot.
The one lead: R_AX_WMAC_TX_INFO0_DEBUG (0xCAE8) reads 0x10914012 in every dead session and 0x10915012 in good ones (bit 12), so the TMAC does issue the response, and the RF path-0 TX registers show it never reaches the RF. Next experiments: a firmware RAM dump dead vs good, and a vendor rtl8852cu A/B on the same unit with a real station answering, to learn whether the vendor bring-up ever shows the state at all.
2. Kestrel host injection on ch161 nearly silent
Both TX50UH units, txdemo TX-only at 6M, 20 ms gap, ch161: 6-10 of ~290 frames witnessed, by either an 8852C or the 8812CU, in good and dead ACK sessions alike. Same setup on ch6: 97-99%. Earlier 8852C -> 8812CU injection A/Bs (~97%) were on ch6. Needs a 5 GHz injection A/B against the vendor driver on this unit before any 5 GHz Kestrel TX number is trusted.
3. 8852C coex init on the C die is a no-op
HalKestrel::coex_mac_init sets ENBT for the 8852B only, so on the 8852C both write_lte calls time out ("Kestrel coex: LTE interface not ready" twice per session) and the GNT stance is skipped. The vendor's 8852C path (coex_8852c.c) does not use the LTE window (mac_write_lte_8852c returns MACNOTSUP); it writes R_AX_GNT_SW_CTRL and R_AX_BTC_CFG / R_AX_BT_CNT_CFG / R_AX_CCA_CFG_0 directly. Cold state read on this unit: GNT_SW_CTRL 0x175775, GNT_VAL 0x118 (BT granted, WL not), BTC_CFG bit 31 clear. Forcing the WiFi-only grant did not change item 1, so this is a correctness cleanup, not a fix.
4. Bench note
The dead rate in item 1 rose through a day of back-to-back sessions on both units and no power cycle reset it. Anyone measuring the 8852C responder late in a session day will see a different rate from the morning; the matrix in AdapterCaps.h should say when in the day its rows were taken.
- Langage dominant
- C
- Étoiles
- 56
- Forks
- 29
- Merge moyen
- 3 h 43 min
- PR mergées (30 j)
- 75
Préparer son environnement
Ce projet ne fournit ni conteneur de développement, ni Dockerfile, ni guide de contribution : l'installation est à votre charge. Commencez par son README, et consultez notre guide de la première contribution pour les étapes générales.
Par où commencer
- Lisez l'issue en entier, puis le guide de contribution du projet.
- Signalez en commentaire que vous la prenez — cela évite que deux personnes fassent le même travail.
- Forkez le dépôt et travaillez sur une branche.
- Ouvrez une pull request qui référence le numéro de l'issue.
Autres issues de OpenIPC/devourer
-
Difficulté 2/5 1-3 heures Accessibilité débutants 82/100
Les mainteneurs répondent en général sous 1 jour
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Peut-être pris @josephnef l’a pris aujourd’hui. Ouverteenhancement
Difficulté 4/5 3-5 jours Accessibilité débutants 42/100
Les mainteneurs répondent en général sous 1 jour
-
Difficulté 5/5 Plus d'une semaine Accessibilité débutants 12/100
OpenIPC/devourer#579 · 1 commentaire ·
Les mainteneurs répondent en général sous 1 jour
-
enhancement
Difficulté 5/5 Plus d'une semaine Accessibilité débutants 12/100
Les mainteneurs répondent en général sous 1 jour
-
enhancement
Difficulté 5/5 Plus d'une semaine Accessibilité débutants 8/100
Les mainteneurs répondent en général sous 1 jour
Toutes les issues de OpenIPC/devourer
Issues similaires
-
Difficulté 2/5 1-3 heures Accessibilité débutants 72/100
Les mainteneurs répondent en général sous 1 jour
-
Needs-Triage
Difficulté 2/5 1-3 heures Accessibilité débutants 66/100
Les mainteneurs répondent en général sous 2 jours
-
issue: bug report
Difficulté 2/5 1-3 heures Accessibilité débutants 82/100
Les mainteneurs répondent en général sous 2 jours
-
cross-platform fix-now
Difficulté 2/5 1-3 heures Accessibilité débutants 76/100
Les mainteneurs répondent en général sous 1 jour
-
feature:index kind:crash status:confirmed triaged
Difficulté 2/5 1-3 heures Accessibilité débutants 77/100
clice-io/clice#1123 · 1 commentaire ·
Les mainteneurs répondent en général sous 1 jour