Follow-ups left open by TxMode::no_agg / NOAGG (#459)

Abierto
#462 0 comentarios 0 reacciones 0 asignados Ver en GitHub

Los mantenedores suelen responder en 1 día

Nadie ha tomado este issue todavía.

Evaluación

Dificultad
5/5
Tiempo estimado
Más de una semana
Aptitud para principiantes
25/100
Tipo de issue
Nueva funcionalidad
Claridad
Bien especificado
Estado de actividad
Activo
Stack tecnológico
c, linux
Área
networking

Línea de trabajo

Start with tests/tx_no_agg_onair.sh for the measurement follow-ups; the issue names no code entry point for the driver ports. First determine which follow-up has suitable hardware and a reproducible bench, then read the prior results from #459. Done means delivering the requested measurements or a validated on-air port; several investigations remain open-ended and hardware-dependent.

Escrito por el modelo de indexación a partir del texto del issue.

Descripción

enhancement

Left open by #459 (TxMode::no_agg / /NOAGG, merged as 87dde96). None blocks the feature as shipped; each is a measurement or a port the PR explicitly did not claim.

  • Cost of occasional flagged frames. Only the every-other-frame worst case was measured (−47 % heard on the 8812EU, −60 % on the 8812CU). The realistic shape, one control frame every N aggregated video frames, is unmeasured. tests/tx_no_agg_onair.sh needs a duty knob (flag every Nth frame) and a goodput reading, not a heard-fps one.
  • Mixed-width fold. The A-MPDU folds bandwidth as well as rate (a 20 MHz frame behind a 40 MHz opener airs at 40). The harness scores rate only. Add a width arm once the witness's rx.seq carries the decoded bandwidth.
  • Port to Jaguar1 / Jaguar2 / MT7612U. tx_no_agg_ok is false there by design. Jaguar2 shares the halmac descriptor (SET_TX_DESC_BK dword2[16]) so it is likely the same two writes; Jaguar1's 8812A descriptor and the MT7612U TXWI need their own look. Each needs an on-air arm, not a code-reading.
  • Cross-rate fold on the 8822C is deeper than on the 8822E (24 % vs 40 % of MCS0 frames kept their rate unflagged, same script, same knobs). Unexplained. Candidates: USB high-speed vs SuperSpeed feed depth, or a die difference in how many MPDUs the MAC waits to accumulate. One unit per die so far.
  • 8812EU on the OpenIPC bench drops off the USB bus about 1 s after the TX bring-up reset (dmesg disconnect + re-enumerate; doctor HEALTHY on EFUSE/fw/RX). It ran a 60 s flood on 2026-09-26, so the bench changed. Rig, not code, but it is why the EU arm was not repeated here.
Lenguaje dominante
C
Estrellas
56
Forks
29
Merge medio
3 h 43 min
PR fusionados (30 d)
75

Preparar el entorno

Este proyecto no incluye contenedor de desarrollo, Dockerfile ni guía de contribución, así que la configuración corre por tu cuenta: empieza por su README y consulta nuestra guía para la primera contribución para los pasos generales.

Primeros pasos

  1. Lee el issue completo y luego la guía de contribución del proyecto.
  2. Comenta en el issue que vas a ocuparte — evita que dos personas hagan lo mismo.
  3. Haz un fork del repositorio y trabaja en una rama.
  4. Abre un pull request que haga referencia al número del issue.

Más de OpenIPC/devourer

Todos los issues de OpenIPC/devourer

Issues similares

Más issues de C

Recibe los nuevos issues en tu correo

Un resumen breve de issues de GitHub para principiantes.