Follow-ups left open by the 8822B DFIR and J3 runtime-thread reviews (#497, #498)

未关闭
#499 11 条评论 0 个 reaction 已指派 0 人 在 GitHub 查看

维护者通常 1 天内回复

还没有人认领这个 Issue。

评估

难度
5/5
预计耗时
一周以上
新手友好度
35/100
Issue 类型
缺陷
描述清晰度
基本清楚
活跃度
活跃
技术栈
c, linux

调研方向

Start with the review findings in issues #497 and #498 and the Jaguar3 notes in src/jaguar3/CLAUDE.md; the payload names no test files or commands. Reproduce the stated transmitter and receiver setups, then investigate each of the four open measurements: runtime-thread duration and chip variants, MCS7 EVM and distance, 2.4 GHz HT40 qualification, and Jaguar1 wide-bandwidth RX. Record results and update the relevant documentation or qualification findings.

由索引模型根据 Issue 内容生成。

描述

enhancement

Things the #497 and #498 reviews measured but did not settle. Bench for all of them: an 8812EU (Jaguar3, 0bda:a81a) transmitting and an 8812BU (8822B cut 3, CF-924AC 0bda:b812) receiving.

1. Does Jaguar3 TX go silent with the runtime thread off, given longer runs or the 8822C? (#498)

src/jaguar3/CLAUDE.md says sustained 5 GHz TX needs the coex runtime thread; without it the coex firmware silences the antenna. On the 8822E I could not reproduce that within 22 s. TX-only, ch36 MCS1/20, 10 000 frames:

rep 1 rep 2
thread on (default) 99.4 % 99.2 %
DEVOURER_J3_RUNTIME=0 99.5 % 99.4 %

Not tested: runs of minutes rather than seconds, the 8822C (8812CU/8822CU), and the upper 5 GHz channels, where pwr_track matters. If the silencing does not reproduce, the CLAUDE.md claim should be narrowed. If it does, the j3_runtime_thread docs should say after how long and on which die.

2. Is MCS7 on this pair really worse at 20 MHz than at 40 MHz?

Same pair, same channel (ch36), same session, 1500 frames per cell:

  • MCS7/20: 34.0 / 63.1 / 54.1 / 43.7 % across four runs, all on byte-identical 20 MHz code paths.
  • MCS7/40: 95.5–98.7 % (after #497).

The 20 MHz spread is far above the usual ±3-point probe noise, and the 20 MHz result is worse than the 40 MHz one, which is backwards. One unexplored lead: in the earlier runs at this distance the rx.txhit RSSI read 102–104, i.e. near-field. At 20 MHz the same TX power is concentrated in half the bandwidth, so this may be receiver saturation, which would show as poor EVM rather than poor RSSI. Check EVM and repeat at more distance (or lower TX power) before believing the number.

3. Re-qualify the 8822B b812 for HT40 on 2.4 GHz

After #497 the b812 is flat up to MCS7 on ch36 HT40 (88.7 / 89.9 / 89.2 / 89.0 / 93.5 / 96.6 % across MCS1/3/4/5/6/7). It was already qualified at 20 MHz. ch6 HT40 is still unmeasured: the 8812EU module is wired with 5 GHz antennas and is not a usable 2.4 GHz transmitter (ch6, 20 MHz: 6M 29.5 %, MCS1 0 %). Repeat the ladder with a transmitter that works on 2.4 GHz.

4. Does Jaguar1 have the same wide-RX hole?

Before #497, rxdemo with DEVOURER_BW=40 delivered nothing on Jaguar2. The 8822B half of that was its RX DFIR being left in the 20 MHz setting (0 % → ~96 % at VHT80). The 8821C path already switched the DFIR by width. Jaguar1 (8812AU/8814AU/8821AU) has not been checked. Run the same A/B: an 8812EU sending HT40/VHT80 on ch36 into an 8812AU at DEVOURER_BW=40/80.

主要语言
C
星标
56
派生
29
平均合并
3 小时 43 分钟
30 天内合并 PR
75

环境准备

这个项目没有提供开发容器、Dockerfile 或贡献指南,环境需要你自己搭建:先看它的 README,通用步骤见我们的新手贡献指南。

从这里开始

  1. 先读完整个 Issue,再读项目的贡献指南。
  2. 在 Issue 下留言说明你要接手 —— 这能避免两个人做同样的事。
  3. Fork 仓库,在一个分支上完成修改。
  4. 提交 Pull Request,并在描述里引用这个 Issue 编号。

OpenIPC/devourer 的其他 Issue

查看 OpenIPC/devourer 的全部 Issue

相似的 Issue

更多 C Issue

把新 issue 发到你的邮箱

精选适合新手参与的 GitHub issue 摘要。