Follow-ups left open by the 8822B DFIR and J3 runtime-thread reviews (#497, #498)
Los mantenedores suelen responder en 1 día
Nadie ha tomado este issue todavía.
Evaluación
- Dificultad
- 5/5
- Tiempo estimado
- Más de una semana
- Aptitud para principiantes
- 35/100
- Tipo de issue
- Error
- Claridad
- Bastante claro
- Estado de actividad
- Activo
- Stack tecnológico
- c, linux
- Área
- embedded-iot, networking, testing
Línea de trabajo
Start with the review findings in issues #497 and #498 and the Jaguar3 notes in src/jaguar3/CLAUDE.md; the payload names no test files or commands. Reproduce the stated transmitter and receiver setups, then investigate each of the four open measurements: runtime-thread duration and chip variants, MCS7 EVM and distance, 2.4 GHz HT40 qualification, and Jaguar1 wide-bandwidth RX. Record results and update the relevant documentation or qualification findings.
Escrito por el modelo de indexación a partir del texto del issue.
Descripción
Things the #497 and #498 reviews measured but did not settle. Bench for all of them: an 8812EU (Jaguar3, 0bda:a81a) transmitting and an 8812BU (8822B cut 3, CF-924AC 0bda:b812) receiving.
1. Does Jaguar3 TX go silent with the runtime thread off, given longer runs or the 8822C? (#498)
src/jaguar3/CLAUDE.md says sustained 5 GHz TX needs the coex runtime thread; without it the coex firmware silences the antenna. On the 8822E I could not reproduce that within 22 s. TX-only, ch36 MCS1/20, 10 000 frames:
| rep 1 | rep 2 | |
|---|---|---|
| thread on (default) | 99.4 % | 99.2 % |
DEVOURER_J3_RUNTIME=0 |
99.5 % | 99.4 % |
Not tested: runs of minutes rather than seconds, the 8822C (8812CU/8822CU), and the upper 5 GHz channels, where pwr_track matters. If the silencing does not reproduce, the CLAUDE.md claim should be narrowed. If it does, the j3_runtime_thread docs should say after how long and on which die.
2. Is MCS7 on this pair really worse at 20 MHz than at 40 MHz?
Same pair, same channel (ch36), same session, 1500 frames per cell:
- MCS7/20: 34.0 / 63.1 / 54.1 / 43.7 % across four runs, all on byte-identical 20 MHz code paths.
- MCS7/40: 95.5–98.7 % (after #497).
The 20 MHz spread is far above the usual ±3-point probe noise, and the 20 MHz result is worse than the 40 MHz one, which is backwards. One unexplored lead: in the earlier runs at this distance the rx.txhit RSSI read 102–104, i.e. near-field. At 20 MHz the same TX power is concentrated in half the bandwidth, so this may be receiver saturation, which would show as poor EVM rather than poor RSSI. Check EVM and repeat at more distance (or lower TX power) before believing the number.
3. Re-qualify the 8822B b812 for HT40 on 2.4 GHz
After #497 the b812 is flat up to MCS7 on ch36 HT40 (88.7 / 89.9 / 89.2 / 89.0 / 93.5 / 96.6 % across MCS1/3/4/5/6/7). It was already qualified at 20 MHz. ch6 HT40 is still unmeasured: the 8812EU module is wired with 5 GHz antennas and is not a usable 2.4 GHz transmitter (ch6, 20 MHz: 6M 29.5 %, MCS1 0 %). Repeat the ladder with a transmitter that works on 2.4 GHz.
4. Does Jaguar1 have the same wide-RX hole?
Before #497, rxdemo with DEVOURER_BW=40 delivered nothing on Jaguar2. The 8822B half of that was its RX DFIR being left in the 20 MHz setting (0 % → ~96 % at VHT80). The 8821C path already switched the DFIR by width. Jaguar1 (8812AU/8814AU/8821AU) has not been checked. Run the same A/B: an 8812EU sending HT40/VHT80 on ch36 into an 8812AU at DEVOURER_BW=40/80.
- Lenguaje dominante
- C
- Estrellas
- 56
- Forks
- 29
- Merge medio
- 3 h 43 min
- PR fusionados (30 d)
- 75
Preparar el entorno
Este proyecto no incluye contenedor de desarrollo, Dockerfile ni guía de contribución, así que la configuración corre por tu cuenta: empieza por su README y consulta nuestra guía para la primera contribución para los pasos generales.
Primeros pasos
- Lee el issue completo y luego la guía de contribución del proyecto.
- Comenta en el issue que vas a ocuparte — evita que dos personas hagan lo mismo.
- Haz un fork del repositorio y trabaja en una rama.
- Abre un pull request que haga referencia al número del issue.
Más de OpenIPC/devourer
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 82/100
Los mantenedores suelen responder en 1 día
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Posiblemente ocupada @josephnef la tomó hoy. Abiertoenhancement
Dificultad 4/5 3-5 días Aptitud para principiantes 42/100
Los mantenedores suelen responder en 1 día
-
Dificultad 5/5 Más de una semana Aptitud para principiantes 12/100
OpenIPC/devourer#579 · 1 comentario ·
Los mantenedores suelen responder en 1 día
-
enhancement
Dificultad 5/5 Más de una semana Aptitud para principiantes 12/100
Los mantenedores suelen responder en 1 día
-
enhancement
Dificultad 5/5 Más de una semana Aptitud para principiantes 8/100
Los mantenedores suelen responder en 1 día
Todos los issues de OpenIPC/devourer
Issues similares
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 72/100
Los mantenedores suelen responder en 1 día
-
Needs-Triage
Dificultad 2/5 1-3 horas Aptitud para principiantes 66/100
Los mantenedores suelen responder en 2 días
-
issue: bug report
Dificultad 2/5 1-3 horas Aptitud para principiantes 82/100
Los mantenedores suelen responder en 2 días
-
cross-platform fix-now
Dificultad 2/5 1-3 horas Aptitud para principiantes 76/100
Los mantenedores suelen responder en 1 día
-
feature:index kind:crash status:confirmed triaged
Dificultad 2/5 1-3 horas Aptitud para principiantes 77/100
clice-io/clice#1123 · 1 comentario ·
Los mantenedores suelen responder en 1 día