Follow-ups left open by the 8822B DFIR and J3 runtime-thread reviews (#497, #498)
Maintainer thường phản hồi trong vòng 1 ngày
Chưa có ai nhận issue này.
Đánh giá
- Độ khó
- 5/5
- Thời gian dự kiến
- Hơn một tuần
- Mức phù hợp với người mới
- 35/100
- Loại issue
- Lỗi
- Độ rõ ràng
- Khá rõ ràng
- Mức độ hoạt động
- Sôi nổi
- Công nghệ
- c, linux
- Lĩnh vực
- embedded-iot, networking, testing
Hướng nghiên cứu
Start with the review findings in issues #497 and #498 and the Jaguar3 notes in src/jaguar3/CLAUDE.md; the payload names no test files or commands. Reproduce the stated transmitter and receiver setups, then investigate each of the four open measurements: runtime-thread duration and chip variants, MCS7 EVM and distance, 2.4 GHz HT40 qualification, and Jaguar1 wide-bandwidth RX. Record results and update the relevant documentation or qualification findings.
Do mô hình lập chỉ mục viết ra từ nội dung của issue.
Mô tả
Things the #497 and #498 reviews measured but did not settle. Bench for all of them: an 8812EU (Jaguar3, 0bda:a81a) transmitting and an 8812BU (8822B cut 3, CF-924AC 0bda:b812) receiving.
1. Does Jaguar3 TX go silent with the runtime thread off, given longer runs or the 8822C? (#498)
src/jaguar3/CLAUDE.md says sustained 5 GHz TX needs the coex runtime thread; without it the coex firmware silences the antenna. On the 8822E I could not reproduce that within 22 s. TX-only, ch36 MCS1/20, 10 000 frames:
| rep 1 | rep 2 | |
|---|---|---|
| thread on (default) | 99.4 % | 99.2 % |
DEVOURER_J3_RUNTIME=0 |
99.5 % | 99.4 % |
Not tested: runs of minutes rather than seconds, the 8822C (8812CU/8822CU), and the upper 5 GHz channels, where pwr_track matters. If the silencing does not reproduce, the CLAUDE.md claim should be narrowed. If it does, the j3_runtime_thread docs should say after how long and on which die.
2. Is MCS7 on this pair really worse at 20 MHz than at 40 MHz?
Same pair, same channel (ch36), same session, 1500 frames per cell:
- MCS7/20: 34.0 / 63.1 / 54.1 / 43.7 % across four runs, all on byte-identical 20 MHz code paths.
- MCS7/40: 95.5–98.7 % (after #497).
The 20 MHz spread is far above the usual ±3-point probe noise, and the 20 MHz result is worse than the 40 MHz one, which is backwards. One unexplored lead: in the earlier runs at this distance the rx.txhit RSSI read 102–104, i.e. near-field. At 20 MHz the same TX power is concentrated in half the bandwidth, so this may be receiver saturation, which would show as poor EVM rather than poor RSSI. Check EVM and repeat at more distance (or lower TX power) before believing the number.
3. Re-qualify the 8822B b812 for HT40 on 2.4 GHz
After #497 the b812 is flat up to MCS7 on ch36 HT40 (88.7 / 89.9 / 89.2 / 89.0 / 93.5 / 96.6 % across MCS1/3/4/5/6/7). It was already qualified at 20 MHz. ch6 HT40 is still unmeasured: the 8812EU module is wired with 5 GHz antennas and is not a usable 2.4 GHz transmitter (ch6, 20 MHz: 6M 29.5 %, MCS1 0 %). Repeat the ladder with a transmitter that works on 2.4 GHz.
4. Does Jaguar1 have the same wide-RX hole?
Before #497, rxdemo with DEVOURER_BW=40 delivered nothing on Jaguar2. The 8822B half of that was its RX DFIR being left in the 20 MHz setting (0 % → ~96 % at VHT80). The 8821C path already switched the DFIR by width. Jaguar1 (8812AU/8814AU/8821AU) has not been checked. Run the same A/B: an 8812EU sending HT40/VHT80 on ch36 into an 8812AU at DEVOURER_BW=40/80.
- Ngôn ngữ chính
- C
- Star
- 56
- Fork
- 29
- Merge trung bình
- 3 giờ 43 phút
- Pull request đã merge (30 ngày)
- 75
Chuẩn bị môi trường
Dự án này không cung cấp dev container, Dockerfile hay hướng dẫn đóng góp, nên bạn cần tự thiết lập môi trường: hãy bắt đầu từ README và xem hướng dẫn đóng góp lần đầu của chúng tôi để biết các bước chung.
Bắt đầu từ đâu
- Đọc hết issue, rồi đọc hướng dẫn đóng góp của dự án.
- Bình luận trên issue rằng bạn sẽ nhận — tránh hai người làm cùng một việc.
- Fork repository và làm thay đổi trên một nhánh.
- Mở pull request có tham chiếu số hiệu của issue.
Issue khác của OpenIPC/devourer
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 82/100
Maintainer thường phản hồi trong vòng 1 ngày
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Có thể đã có người làm @josephnef đã nhận hôm nay. Đang mởenhancement
Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 42/100
Maintainer thường phản hồi trong vòng 1 ngày
-
Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 12/100
OpenIPC/devourer#579 · 1 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày
-
enhancement
Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 12/100
Maintainer thường phản hồi trong vòng 1 ngày
-
enhancement
Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 8/100
Maintainer thường phản hồi trong vòng 1 ngày
Tất cả issue của OpenIPC/devourer
Issue tương tự
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 72/100
Maintainer thường phản hồi trong vòng 1 ngày
-
Needs-Triage
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 66/100
Maintainer thường phản hồi trong vòng 2 ngày
-
issue: bug report
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 82/100
Maintainer thường phản hồi trong vòng 2 ngày
-
cross-platform fix-now
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 76/100
Maintainer thường phản hồi trong vòng 1 ngày
-
feature:index kind:crash status:confirmed triaged
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 77/100
clice-io/clice#1123 · 1 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày