Request for guidance on manual 10.9 build - RPi 4
まだ誰も着手していません。
評価
- 難易度
- 4/5
- 見積もり時間
- 3〜5日
- 初心者へのやさしさ
- 25/100
- issue の種類
- バグ
- 明瞭さ
- 説明が足りない
- 活発さ
- 停滞
調査の方向性
Start with README.debian and the reported 0.10.9 configure/debuild commands; check which dependencies are available on Debian 11 arm64 and how HTTP support is selected. Done means documenting a reproducible install or build path and confirming olad plus the web UI at http://localhost:9090 on the Raspberry Pi.
索引モデルが issue の本文から書いたものです。
説明
I could really use some direction, I thought I was on the right track but now I'm not sure.
Here's what I'm trying to do,
I'm trying to use olad to confirm that my most basic setup is working before I dive any deeper with DMX. My setup is a raspberry pi 4 running raspberry pi os 64-lite, attached via uart/gpio to a dmx plug, that is in turn attached to a dmx cable and a dmx capable strobe light. I just want to be able to turn the light on/off to prove the hardware works before anything more advanced.
Here's where I'm at,
Initially I installed the ola package from the debian package repository. For raspberry pi os, that's still bullseye debian based, so it picked up ola 0.10.8. I got the web ui working but in the logs I saw the message:
... Failed to set baud rate to 250k
So I found the bugs / support tickets around that:
https://github.com/OpenLightingProject/ola/issues/1749
https://github.com/OpenLightingProject/ola/pull/1760
https://github.com/OpenLightingProject/ola/issues/1884
In particular I saw this message:
https://github.com/OpenLightingProject/ola/issues/1884#issuecomment-1646271477
So I tried to give building ola a shot.
Building 10.9 Attempt
- I reimaged the raspberrypi to start from scratch. (raspberrypi os 64-bit lite, kernel 6.1, debian 11/bullseye from May 3rd)
- I grabbed the 10.9.tar.gz from https://github.com/OpenLightingProject/ola/releases/download/0.10.9/ola-0.10.9.tar.gz
- Initially I tried just "debuild", as per https://github.com/OpenLightingProject/ola/blob/master/README.debian but I got some errors with dependencies, specifically,
~/ola/ola-0.10.9 $ debuild
dpkg-buildpackage -us -uc -ui
dpkg-buildpackage: info: source package ola
dpkg-buildpackage: info: source version 0.10.9-1
dpkg-buildpackage: info: source distribution unstable
dpkg-buildpackage: info: source changed by Peter Newman <[email protected]>
dpkg-source --before-build .
dpkg-buildpackage: info: host architecture arm64
dpkg-source: info: using options from ola-0.10.9/debian/source/local-options: --single-debian-patch
dpkg-checkbuilddeps: error: Unmet build dependencies: python python-protobuf libusb-1.0-0-dev libftdi1-dev liblo-dev libmicrohttpd-dev libncurses5-dev libavahi-client-dev python-numpy
dpkg-buildpackage: warning: build dependencies/conflicts unsatisfied; aborting
dpkg-buildpackage: warning: (Use -d flag to override.)
debuild: fatal error at line 1182:
dpkg-buildpackage -us -uc -ui failed
I tried to install all the dependencies from the error in one big apt install but some of them could not be identified, at least python-protobuf python-numpy
So, I went back to https://github.com/OpenLightingProject/ola/issues/1884
and tried to use these instructions,
./configure --enable-rdm-tests
make
make check
sudo make install
sudo ldconfig
Following that, I installed packages as ./configure needed, although when I got to python-protobuf, I instead installed python3-pip followed by
pip install protobuf
which seemed to get me past the configure failure.
After all that it DID seem like I had ola:
~/ola/ola-0.10.9 $ olad -v
OLA olad version: 0.10.9
It seems to run fine, but now I can't seem to get back to the Web UI. This is a headless install.
So, Questions,
- What is the preferred method to build ola for non-development use?
- If the preferred install method is via debuild, how can I get past this error?
dpkg-checkbuilddeps: error: Unmet build dependencies: python python-protobuf python-numpySee below. - How do I go about enabling the web ui? Is this a build option? I noticed this:
"If you built OLA with http support you can just use the web interface on http://localhost:9090" (source: https://www.openlighting.org/ola/getting-started/using-ola/ )
Appendix - Errors with dependent package install?
~# apt install python python-protobuf python-numpy
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
Note, selecting 'python-is-python2' instead of 'python'
Package python-numpy is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
E: Unable to locate package python-protobuf
E: Package 'python-numpy' has no installation candidate
- 主要言語
- C++
- スター
- 773
- フォーク
- 233
- PR マージ指標
- 30日以内にマージされた PR はありません
環境構築
- Dockerfile・Docker Compose ファイルなし
- プルリクエストのテンプレートなし
- コントリビューションガイドを読む
はじめの一歩
- issue を最後まで読み、次にプロジェクトのコントリビューションガイドを読みます。
- 着手することを issue にコメントします — 二人が同じ作業をするのを防げます。
- リポジトリをフォークし、ブランチを切って変更します。
- issue 番号を参照したプルリクエストを送ります。
OpenLightingProject/ola のほかの issue
-
難易度 2/5 1〜3時間 初心者へのやさしさ 70/100
OpenLightingProject/ola#2075 ·
-
Digital Enlightenment / FX5 not recognized対応中かも このイシューにリンクされたプルリクエストがオープン中、またはマージ済みです。 オープンquestion Type-DeviceSupport
難易度 4/5 3〜5日 初心者へのやさしさ 35/100
OpenLightingProject/ola#2056 · コメント 2 件 ·
-
難易度 3/5 1〜2日 初心者へのやさしさ 55/100
OpenLightingProject/ola#2055 ·
-
Difficulty-Medium Language-C++ Maintainability OpSys-All
難易度 4/5 3〜5日 初心者へのやさしさ 45/100
OpenLightingProject/ola#2053 · コメント 1 件 ·
-
v0.11.0再び着手できるかも @peternewman が 227 日前に担当しましたが、オープン中のプルリクエストはありません。 オープン
OpenLightingProject/ola#2038 · コメント 18 件 · 担当者 2 名 ·
OpenLightingProject/ola の issue をすべて見る
似ている issue
-
documentation
難易度 1/5 1時間未満 初心者へのやさしさ 86/100
Awesome-Embedded-Learning-Studio/Tutorial_AwesomeModernCPP#335 ·
メンテナーはふだん 1 日以内に返信
-
難易度 2/5 1〜3時間 初心者へのやさしさ 76/100
deepseek-ai/DeepEP#830 ·
メンテナーはふだん 1 日以内に返信
-
難易度 2/5 1〜3時間 初心者へのやさしさ 66/100
google-ai-edge/LiteRT-LM#4701 ·
メンテナーはふだん 1 日以内に返信
-
難易度 2/5 1〜3時間 初心者へのやさしさ 82/100
HarperFast/rocksdb-js#1131 ·
メンテナーはふだん 1 日以内に返信
-
Swapped cache lookups in ScanModelAndDecideAllDiffExpansion対応中かも @Lian292213 が今日担当しました。 オープン
難易度 2/5 1〜3時間 初心者へのやさしさ 68/100
メンテナーはふだん 1 日以内に返信