Request for guidance on manual 10.9 build - RPi 4
Nessuno ha ancora preso questa issue.
Valutazione
- Difficoltà
- 4/5
- Tempo stimato
- 3-5 giorni
- Idoneità per principianti
- 25/100
- Tipo di issue
- Bug
- Chiarezza
- Da chiarire
- Stato di attività
- Ferma
- Ambito
- build-system, embedded-iot, web-dev
Direzione di ricerca
Start with README.debian and the reported 0.10.9 configure/debuild commands; check which dependencies are available on Debian 11 arm64 and how HTTP support is selected. Done means documenting a reproducible install or build path and confirming olad plus the web UI at http://localhost:9090 on the Raspberry Pi.
Scritto dal modello di indicizzazione a partire dal testo della issue.
Descrizione
I could really use some direction, I thought I was on the right track but now I'm not sure.
Here's what I'm trying to do,
I'm trying to use olad to confirm that my most basic setup is working before I dive any deeper with DMX. My setup is a raspberry pi 4 running raspberry pi os 64-lite, attached via uart/gpio to a dmx plug, that is in turn attached to a dmx cable and a dmx capable strobe light. I just want to be able to turn the light on/off to prove the hardware works before anything more advanced.
Here's where I'm at,
Initially I installed the ola package from the debian package repository. For raspberry pi os, that's still bullseye debian based, so it picked up ola 0.10.8. I got the web ui working but in the logs I saw the message:
... Failed to set baud rate to 250k
So I found the bugs / support tickets around that:
https://github.com/OpenLightingProject/ola/issues/1749
https://github.com/OpenLightingProject/ola/pull/1760
https://github.com/OpenLightingProject/ola/issues/1884
In particular I saw this message:
https://github.com/OpenLightingProject/ola/issues/1884#issuecomment-1646271477
So I tried to give building ola a shot.
Building 10.9 Attempt
- I reimaged the raspberrypi to start from scratch. (raspberrypi os 64-bit lite, kernel 6.1, debian 11/bullseye from May 3rd)
- I grabbed the 10.9.tar.gz from https://github.com/OpenLightingProject/ola/releases/download/0.10.9/ola-0.10.9.tar.gz
- Initially I tried just "debuild", as per https://github.com/OpenLightingProject/ola/blob/master/README.debian but I got some errors with dependencies, specifically,
~/ola/ola-0.10.9 $ debuild
dpkg-buildpackage -us -uc -ui
dpkg-buildpackage: info: source package ola
dpkg-buildpackage: info: source version 0.10.9-1
dpkg-buildpackage: info: source distribution unstable
dpkg-buildpackage: info: source changed by Peter Newman <[email protected]>
dpkg-source --before-build .
dpkg-buildpackage: info: host architecture arm64
dpkg-source: info: using options from ola-0.10.9/debian/source/local-options: --single-debian-patch
dpkg-checkbuilddeps: error: Unmet build dependencies: python python-protobuf libusb-1.0-0-dev libftdi1-dev liblo-dev libmicrohttpd-dev libncurses5-dev libavahi-client-dev python-numpy
dpkg-buildpackage: warning: build dependencies/conflicts unsatisfied; aborting
dpkg-buildpackage: warning: (Use -d flag to override.)
debuild: fatal error at line 1182:
dpkg-buildpackage -us -uc -ui failed
I tried to install all the dependencies from the error in one big apt install but some of them could not be identified, at least python-protobuf python-numpy
So, I went back to https://github.com/OpenLightingProject/ola/issues/1884
and tried to use these instructions,
./configure --enable-rdm-tests
make
make check
sudo make install
sudo ldconfig
Following that, I installed packages as ./configure needed, although when I got to python-protobuf, I instead installed python3-pip followed by
pip install protobuf
which seemed to get me past the configure failure.
After all that it DID seem like I had ola:
~/ola/ola-0.10.9 $ olad -v
OLA olad version: 0.10.9
It seems to run fine, but now I can't seem to get back to the Web UI. This is a headless install.
So, Questions,
- What is the preferred method to build ola for non-development use?
- If the preferred install method is via debuild, how can I get past this error?
dpkg-checkbuilddeps: error: Unmet build dependencies: python python-protobuf python-numpySee below. - How do I go about enabling the web ui? Is this a build option? I noticed this:
"If you built OLA with http support you can just use the web interface on http://localhost:9090" (source: https://www.openlighting.org/ola/getting-started/using-ola/ )
Appendix - Errors with dependent package install?
~# apt install python python-protobuf python-numpy
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
Note, selecting 'python-is-python2' instead of 'python'
Package python-numpy is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
E: Unable to locate package python-protobuf
E: Package 'python-numpy' has no installation candidate
- Lingua principale
- C++
- Stelle
- 771
- Fork
- 234
- Metriche di merge delle PR
- Nessuna PR unita negli ultimi 30g
Preparare l'ambiente
- Nessun Dockerfile né file Docker Compose
- Nessun modello di pull request
- Leggi la guida per i contributori
Come iniziare
- Leggi tutta la issue e poi la guida ai contributi del progetto.
- Commenta sulla issue per dire che te ne occupi tu — evita che due persone facciano lo stesso lavoro.
- Fai un fork del repository e lavora su un branch.
- Apri una pull request che faccia riferimento al numero della issue.
Altre issue di OpenLightingProject/ola
-
Difficoltà 2/5 1-3 ore Idoneità per principianti 70/100
OpenLightingProject/ola#2075 ·
-
Digital Enlightenment / FX5 not recognizedForse già presa Una pull request collegata a questa issue è aperta o già unita. Apertaquestion Type-DeviceSupport
Difficoltà 4/5 3-5 giorni Idoneità per principianti 35/100
OpenLightingProject/ola#2056 · 2 commenti ·
-
Difficoltà 3/5 1-2 giorni Idoneità per principianti 55/100
OpenLightingProject/ola#2055 ·
-
Difficulty-Medium Language-C++ Maintainability OpSys-All
Difficoltà 4/5 3-5 giorni Idoneità per principianti 45/100
OpenLightingProject/ola#2053 · 1 commento ·
-
v0.11.0Forse di nuovo libera @peternewman l’ha presa 227 giorni fa e non c’è nessuna pull request aperta. Aperta
OpenLightingProject/ola#2038 · 18 commenti · 2 assegnatari ·
Tutte le issue di OpenLightingProject/ola
Issue simili
-
Difficoltà 2/5 1-3 ore Idoneità per principianti 76/100
deepseek-ai/DeepEP#830 ·
I maintainer di solito rispondono entro 1 giorno
-
Difficoltà 2/5 1-3 ore Idoneità per principianti 66/100
google-ai-edge/LiteRT-LM#4701 ·
I maintainer di solito rispondono entro 1 giorno
-
Difficoltà 2/5 1-3 ore Idoneità per principianti 82/100
HarperFast/rocksdb-js#1131 ·
I maintainer di solito rispondono entro 1 giorno
-
Swapped cache lookups in ScanModelAndDecideAllDiffExpansionForse già presa @Lian292213 l’ha presa oggi. Aperta
Difficoltà 2/5 1-3 ore Idoneità per principianti 68/100
I maintainer di solito rispondono entro 1 giorno
-
area/daemon bug good first issue platform/linux priority/p2
Difficoltà 2/5 1-3 ore Idoneità per principianti 72/100
ToshiNamura/Deimos#5 ·