Request for guidance on manual 10.9 build - RPi 4
Nadie ha tomado este issue todavía.
Evaluación
- Dificultad
- 4/5
- Tiempo estimado
- 3-5 días
- Aptitud para principiantes
- 25/100
- Tipo de issue
- Error
- Claridad
- Necesita aclaración
- Estado de actividad
- Estancado
- Área
- build-system, embedded-iot, web-dev
Línea de trabajo
Start with README.debian and the reported 0.10.9 configure/debuild commands; check which dependencies are available on Debian 11 arm64 and how HTTP support is selected. Done means documenting a reproducible install or build path and confirming olad plus the web UI at http://localhost:9090 on the Raspberry Pi.
Escrito por el modelo de indexación a partir del texto del issue.
Descripción
I could really use some direction, I thought I was on the right track but now I'm not sure.
Here's what I'm trying to do,
I'm trying to use olad to confirm that my most basic setup is working before I dive any deeper with DMX. My setup is a raspberry pi 4 running raspberry pi os 64-lite, attached via uart/gpio to a dmx plug, that is in turn attached to a dmx cable and a dmx capable strobe light. I just want to be able to turn the light on/off to prove the hardware works before anything more advanced.
Here's where I'm at,
Initially I installed the ola package from the debian package repository. For raspberry pi os, that's still bullseye debian based, so it picked up ola 0.10.8. I got the web ui working but in the logs I saw the message:
... Failed to set baud rate to 250k
So I found the bugs / support tickets around that:
https://github.com/OpenLightingProject/ola/issues/1749
https://github.com/OpenLightingProject/ola/pull/1760
https://github.com/OpenLightingProject/ola/issues/1884
In particular I saw this message:
https://github.com/OpenLightingProject/ola/issues/1884#issuecomment-1646271477
So I tried to give building ola a shot.
Building 10.9 Attempt
- I reimaged the raspberrypi to start from scratch. (raspberrypi os 64-bit lite, kernel 6.1, debian 11/bullseye from May 3rd)
- I grabbed the 10.9.tar.gz from https://github.com/OpenLightingProject/ola/releases/download/0.10.9/ola-0.10.9.tar.gz
- Initially I tried just "debuild", as per https://github.com/OpenLightingProject/ola/blob/master/README.debian but I got some errors with dependencies, specifically,
~/ola/ola-0.10.9 $ debuild
dpkg-buildpackage -us -uc -ui
dpkg-buildpackage: info: source package ola
dpkg-buildpackage: info: source version 0.10.9-1
dpkg-buildpackage: info: source distribution unstable
dpkg-buildpackage: info: source changed by Peter Newman <[email protected]>
dpkg-source --before-build .
dpkg-buildpackage: info: host architecture arm64
dpkg-source: info: using options from ola-0.10.9/debian/source/local-options: --single-debian-patch
dpkg-checkbuilddeps: error: Unmet build dependencies: python python-protobuf libusb-1.0-0-dev libftdi1-dev liblo-dev libmicrohttpd-dev libncurses5-dev libavahi-client-dev python-numpy
dpkg-buildpackage: warning: build dependencies/conflicts unsatisfied; aborting
dpkg-buildpackage: warning: (Use -d flag to override.)
debuild: fatal error at line 1182:
dpkg-buildpackage -us -uc -ui failed
I tried to install all the dependencies from the error in one big apt install but some of them could not be identified, at least python-protobuf python-numpy
So, I went back to https://github.com/OpenLightingProject/ola/issues/1884
and tried to use these instructions,
./configure --enable-rdm-tests
make
make check
sudo make install
sudo ldconfig
Following that, I installed packages as ./configure needed, although when I got to python-protobuf, I instead installed python3-pip followed by
pip install protobuf
which seemed to get me past the configure failure.
After all that it DID seem like I had ola:
~/ola/ola-0.10.9 $ olad -v
OLA olad version: 0.10.9
It seems to run fine, but now I can't seem to get back to the Web UI. This is a headless install.
So, Questions,
- What is the preferred method to build ola for non-development use?
- If the preferred install method is via debuild, how can I get past this error?
dpkg-checkbuilddeps: error: Unmet build dependencies: python python-protobuf python-numpySee below. - How do I go about enabling the web ui? Is this a build option? I noticed this:
"If you built OLA with http support you can just use the web interface on http://localhost:9090" (source: https://www.openlighting.org/ola/getting-started/using-ola/ )
Appendix - Errors with dependent package install?
~# apt install python python-protobuf python-numpy
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
Note, selecting 'python-is-python2' instead of 'python'
Package python-numpy is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
E: Unable to locate package python-protobuf
E: Package 'python-numpy' has no installation candidate
- Lenguaje dominante
- C++
- Estrellas
- 773
- Forks
- 233
- Métricas de merge de PR
- Sin PR fusionados en 30 d
Preparar el entorno
- Sin Dockerfile ni archivo de Docker Compose
- Sin plantilla de pull request
- Leer la guía de contribución
Primeros pasos
- Lee el issue completo y luego la guía de contribución del proyecto.
- Comenta en el issue que vas a ocuparte — evita que dos personas hagan lo mismo.
- Haz un fork del repositorio y trabaja en una rama.
- Abre un pull request que haga referencia al número del issue.
Más de OpenLightingProject/ola
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 70/100
OpenLightingProject/ola#2075 ·
-
Digital Enlightenment / FX5 not recognizedPosiblemente ocupada Un pull request vinculado a esta issue está abierto o ya se fusionó. Abiertoquestion Type-DeviceSupport
Dificultad 4/5 3-5 días Aptitud para principiantes 35/100
OpenLightingProject/ola#2056 · 2 comentarios ·
-
Dificultad 3/5 1-2 días Aptitud para principiantes 55/100
OpenLightingProject/ola#2055 ·
-
Difficulty-Medium Language-C++ Maintainability OpSys-All
Dificultad 4/5 3-5 días Aptitud para principiantes 45/100
OpenLightingProject/ola#2053 · 1 comentario ·
-
v0.11.0Quizá libre de nuevo @peternewman la tomó hace 227 días y no hay ningún pull request abierto. Abierto
OpenLightingProject/ola#2038 · 18 comentarios · 2 asignados ·
Todos los issues de OpenLightingProject/ola
Issues similares
-
[内容勘误] STL常用模式章节实战演练中代码有问题Abiertodocumentation
Dificultad 1/5 Menos de una hora Aptitud para principiantes 86/100
Awesome-Embedded-Learning-Studio/Tutorial_AwesomeModernCPP#335 ·
Los mantenedores suelen responder en 1 día
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 76/100
deepseek-ai/DeepEP#830 ·
Los mantenedores suelen responder en 1 día
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 66/100
google-ai-edge/LiteRT-LM#4701 ·
Los mantenedores suelen responder en 1 día
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 82/100
HarperFast/rocksdb-js#1131 ·
Los mantenedores suelen responder en 1 día
-
Swapped cache lookups in ScanModelAndDecideAllDiffExpansionPosiblemente ocupada @Lian292213 la tomó hoy. Abierto
Dificultad 2/5 1-3 horas Aptitud para principiantes 68/100
Los mantenedores suelen responder en 1 día