Jaguar2 8822BU TX does not air at level for ~4 s after its first submitted frame
メンテナーはふだん 1 日以内に返信
まだ誰も着手していません。
評価
- 難易度
- 4/5
- 見積もり時間
- 3〜5日
- 初心者へのやさしさ
- 35/100
- issue の種類
- バグ
- 明瞭さ
- おおむね明確
- 活発さ
- 活発
- 技術スタック
- c, linux
- 領域
- embedded-iot
調査の方向性
Start with the mentioned tests/busy_window_probe.cpp and tests/busy_window_probe.sh, then run the reproduction with FLOOD_SETTLE_S=0 using a Jaguar3 sensor and RTL8822BU T3U on channel 165. Compare the first submitted frame with the sensor’s busy-window readings, and first A/B test the onset using the vendor rtl88x2bu driver. Done means identifying whether the initial ~4-second low-reading period is reproducible and whether it is specific to this port; the cause is not established in the issue.
索引モデルが issue の本文から書いたものです。
説明
What was seen
A Jaguar2 RTL8822BU (TP-Link Archer T3U, 2357:012d) driven by txdemo at max duty (DEVOURER_TX_RATE=MCS1 DEVOURER_TX_GAP_US=0, ch165) does not air at level for ~4 s after its first submitted frame. Found while re-validating #437 on this bench: the Jaguar3 sensor's first armed busy window read a valid 0% on a channel that was 64% busy a second later.
Sensor first, flooder second (RTL8812CU sensor, 120 × 50 ms ArmChannelBusy windows, tests/busy_window_probe.cpp):
| cycle | flooder's first bulk_send |
sensor first non-zero window | gap |
|---|---|---|---|
| 1 | window #37 | window #99 (11%, then 61-65%) | ~62 windows ≈ 4.0 s |
| 2 | window #38 | window #100 (56%, then 61-65%) | ~62 windows ≈ 4.0 s |
The complementary arm, flooder first: 5/5 sensor bring-ups launched 4 s after the flooder saw seven 50 ms windows at 0% before the load appeared; 5/5 with the flooder running >10 s were at 61-65% from the first window. 15 s of sensor idle before bring-up changes nothing. So it is the transmitter's onset, not the receiver's.
txdemo reports submitted frames from its first bulk_send, and the bulk-OUT calls return OK, so from the host's side the flooder is transmitting the whole time.
Why it matters
- Any harness that starts a Jaguar2 flooder and measures within ~5 s measures an idle channel and cannot tell.
tests/busy_window_probe.shnow waits for it (measured value + margin,FLOOD_SETTLE_S), and the sensing doc carries the caveat; other loaded-channel harnesses that use a Jaguar2 flooder should be checked. - On the link itself: the first ~4 s of a Jaguar2 TX session are, as far as a co-channel receiver is concerned, not at the level the rest of the session runs at. For a quick-connect FPV downlink that is the part of the session that matters most.
What is not known
- Whether it is power (weak), a wrong channel, or no radiation at all during the window — the sensor's CLM cannot tell those apart. An SDR read of the first 5 s would.
- What ends it at ~4 s. Candidates in the Jaguar2 bring-up: the thermal/pwr-track first tick, the DIG/EDCCA operating point settling, or something in the USB smart-switch sequence on this unit (the T3U boots USB2 and re-enumerates USB3).
- Whether the 8821CU and the CF-924AC (
0bda:b812, external antennas) do the same — only the T3U was the flooder here. - Whether the vendor
rtl88x2budriver shows the same onset. That A/B is the first thing to run before attributing it to the port.
Reproduce
Bench with a Jaguar3 sensor and the T3U on ch165, branch of #437:
sudo tests/busy_window_probe.sh # with FLOOD_SETTLE_S=0 the first arm reads 0%
Or the sensor-first form: start BusyWindowProbe --vid 0x0bda --pid 0xc812 --channel 165 --mode window --window-ms 50 --reps 120, then txdemo on the T3U ~3 s later, and count windows between its first bulk_send and the sensor's first non-zero reading.
🤖 Generated with Claude Code
- 主要言語
- C
- スター
- 56
- フォーク
- 29
- 平均マージ
- 3時間 43分
- マージ済み PR(30日)
- 75
環境構築
このプロジェクトには開発コンテナ、Dockerfile、コントリビューションガイドがありません。まず README を読み、一般的な手順ははじめてのコントリビューションガイドを参照してください。
はじめの一歩
- issue を最後まで読み、次にプロジェクトのコントリビューションガイドを読みます。
- 着手することを issue にコメントします — 二人が同じ作業をするのを防げます。
- リポジトリをフォークし、ブランチを切って変更します。
- issue 番号を参照したプルリクエストを送ります。
OpenIPC/devourer のほかの issue
-
難易度 2/5 1〜3時間 初心者へのやさしさ 82/100
メンテナーはふだん 1 日以内に返信
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)対応中かも @josephnef が今日担当しました。 オープンenhancement
難易度 4/5 3〜5日 初心者へのやさしさ 42/100
メンテナーはふだん 1 日以内に返信
-
難易度 5/5 1週間以上 初心者へのやさしさ 12/100
OpenIPC/devourer#579 · コメント 1 件 ·
メンテナーはふだん 1 日以内に返信
-
enhancement
難易度 5/5 1週間以上 初心者へのやさしさ 12/100
メンテナーはふだん 1 日以内に返信
-
enhancement
難易度 5/5 1週間以上 初心者へのやさしさ 8/100
メンテナーはふだん 1 日以内に返信
OpenIPC/devourer の issue をすべて見る
似ている issue
-
難易度 2/5 1〜3時間 初心者へのやさしさ 72/100
メンテナーはふだん 1 日以内に返信
-
Needs-Triage
難易度 2/5 1〜3時間 初心者へのやさしさ 66/100
メンテナーはふだん 2 日以内に返信
-
issue: bug report
難易度 2/5 1〜3時間 初心者へのやさしさ 82/100
メンテナーはふだん 2 日以内に返信
-
cross-platform fix-now
難易度 2/5 1〜3時間 初心者へのやさしさ 76/100
メンテナーはふだん 1 日以内に返信
-
feature:index kind:crash status:confirmed triaged
難易度 2/5 1〜3時間 初心者へのやさしさ 77/100
clice-io/clice#1123 · コメント 1 件 ·
メンテナーはふだん 1 日以内に返信