Jaguar2 8822BU TX does not air at level for ~4 s after its first submitted frame
Maintainer thường phản hồi trong vòng 1 ngày
Chưa có ai nhận issue này.
Đánh giá
- Độ khó
- 4/5
- Thời gian dự kiến
- 3-5 ngày
- Mức phù hợp với người mới
- 35/100
- Loại issue
- Lỗi
- Độ rõ ràng
- Khá rõ ràng
- Mức độ hoạt động
- Sôi nổi
- Công nghệ
- c, linux
- Lĩnh vực
- embedded-iot
Hướng nghiên cứu
Start with the mentioned tests/busy_window_probe.cpp and tests/busy_window_probe.sh, then run the reproduction with FLOOD_SETTLE_S=0 using a Jaguar3 sensor and RTL8822BU T3U on channel 165. Compare the first submitted frame with the sensor’s busy-window readings, and first A/B test the onset using the vendor rtl88x2bu driver. Done means identifying whether the initial ~4-second low-reading period is reproducible and whether it is specific to this port; the cause is not established in the issue.
Do mô hình lập chỉ mục viết ra từ nội dung của issue.
Mô tả
What was seen
A Jaguar2 RTL8822BU (TP-Link Archer T3U, 2357:012d) driven by txdemo at max duty (DEVOURER_TX_RATE=MCS1 DEVOURER_TX_GAP_US=0, ch165) does not air at level for ~4 s after its first submitted frame. Found while re-validating #437 on this bench: the Jaguar3 sensor's first armed busy window read a valid 0% on a channel that was 64% busy a second later.
Sensor first, flooder second (RTL8812CU sensor, 120 × 50 ms ArmChannelBusy windows, tests/busy_window_probe.cpp):
| cycle | flooder's first bulk_send |
sensor first non-zero window | gap |
|---|---|---|---|
| 1 | window #37 | window #99 (11%, then 61-65%) | ~62 windows ≈ 4.0 s |
| 2 | window #38 | window #100 (56%, then 61-65%) | ~62 windows ≈ 4.0 s |
The complementary arm, flooder first: 5/5 sensor bring-ups launched 4 s after the flooder saw seven 50 ms windows at 0% before the load appeared; 5/5 with the flooder running >10 s were at 61-65% from the first window. 15 s of sensor idle before bring-up changes nothing. So it is the transmitter's onset, not the receiver's.
txdemo reports submitted frames from its first bulk_send, and the bulk-OUT calls return OK, so from the host's side the flooder is transmitting the whole time.
Why it matters
- Any harness that starts a Jaguar2 flooder and measures within ~5 s measures an idle channel and cannot tell.
tests/busy_window_probe.shnow waits for it (measured value + margin,FLOOD_SETTLE_S), and the sensing doc carries the caveat; other loaded-channel harnesses that use a Jaguar2 flooder should be checked. - On the link itself: the first ~4 s of a Jaguar2 TX session are, as far as a co-channel receiver is concerned, not at the level the rest of the session runs at. For a quick-connect FPV downlink that is the part of the session that matters most.
What is not known
- Whether it is power (weak), a wrong channel, or no radiation at all during the window — the sensor's CLM cannot tell those apart. An SDR read of the first 5 s would.
- What ends it at ~4 s. Candidates in the Jaguar2 bring-up: the thermal/pwr-track first tick, the DIG/EDCCA operating point settling, or something in the USB smart-switch sequence on this unit (the T3U boots USB2 and re-enumerates USB3).
- Whether the 8821CU and the CF-924AC (
0bda:b812, external antennas) do the same — only the T3U was the flooder here. - Whether the vendor
rtl88x2budriver shows the same onset. That A/B is the first thing to run before attributing it to the port.
Reproduce
Bench with a Jaguar3 sensor and the T3U on ch165, branch of #437:
sudo tests/busy_window_probe.sh # with FLOOD_SETTLE_S=0 the first arm reads 0%
Or the sensor-first form: start BusyWindowProbe --vid 0x0bda --pid 0xc812 --channel 165 --mode window --window-ms 50 --reps 120, then txdemo on the T3U ~3 s later, and count windows between its first bulk_send and the sensor's first non-zero reading.
🤖 Generated with Claude Code
- Ngôn ngữ chính
- C
- Star
- 56
- Fork
- 29
- Merge trung bình
- 3 giờ 43 phút
- Pull request đã merge (30 ngày)
- 75
Chuẩn bị môi trường
Dự án này không cung cấp dev container, Dockerfile hay hướng dẫn đóng góp, nên bạn cần tự thiết lập môi trường: hãy bắt đầu từ README và xem hướng dẫn đóng góp lần đầu của chúng tôi để biết các bước chung.
Bắt đầu từ đâu
- Đọc hết issue, rồi đọc hướng dẫn đóng góp của dự án.
- Bình luận trên issue rằng bạn sẽ nhận — tránh hai người làm cùng một việc.
- Fork repository và làm thay đổi trên một nhánh.
- Mở pull request có tham chiếu số hiệu của issue.
Issue khác của OpenIPC/devourer
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 82/100
Maintainer thường phản hồi trong vòng 1 ngày
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Có thể đã có người làm @josephnef đã nhận hôm nay. Đang mởenhancement
Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 42/100
Maintainer thường phản hồi trong vòng 1 ngày
-
Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 12/100
OpenIPC/devourer#579 · 1 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày
-
enhancement
Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 12/100
Maintainer thường phản hồi trong vòng 1 ngày
-
enhancement
Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 8/100
Maintainer thường phản hồi trong vòng 1 ngày
Tất cả issue của OpenIPC/devourer
Issue tương tự
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 72/100
Maintainer thường phản hồi trong vòng 1 ngày
-
Needs-Triage
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 66/100
Maintainer thường phản hồi trong vòng 2 ngày
-
issue: bug report
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 82/100
Maintainer thường phản hồi trong vòng 2 ngày
-
cross-platform fix-now
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 76/100
Maintainer thường phản hồi trong vòng 1 ngày
-
feature:index kind:crash status:confirmed triaged
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 77/100
clice-io/clice#1123 · 1 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày