40 MHz / 80 MHz coverage left open by #352: 8814AU, 8821AU, Jaguar2 RX, 80 MHz, other channels
Maintainers usually reply within 1 day
Nobody has claimed this yet.
Assessment
- Difficulty
- 4/5
- Estimated time
- 3-5 days
- Newbie friendliness
- 34/100
- Issue type
- Feature
- Clarity
- Mostly clear
- Activity status
- Active
- Tech stack
- c
- Domain
- networking, testing
Research direction
Start with tests/bw40_pair_onair.sh and docs/vht-on-2g4.md, then review the existing Jaguar2 40 MHz transmit test and the rtw_get_center_ch handling referenced in the issue. The issue calls for measurements across additional chips, receive paths, bandwidths and channels; 80 MHz coverage also needs new cells and rates. Done means recording those measurements with per-leg 20 MHz controls and peer power sweeps.
Written by the indexing model from the issue text.
Description
What is left unmeasured after #352
#352 (Jaguar1 40 MHz dead both ways) closed on 2026-11-09: the cause was the HT40 centre-channel tune fixed in #500, verified on an RTL8812AU against an RTL8852CU with tests/bw40_pair_onair.sh (branch bw40-352-verify). That verification covered exactly one die, one channel and one width. These cells are still open:
- RTL8814AU and RTL8821AU at 40 MHz. Both go through the same
rtw_get_center_chrule as the 8812AU but neither has been measured (noted as unverified in #500 as well). The 8814AU needs the pinned-kernel VM for any vendor-driver control and is judged by its devourer-TX cells only. - Jaguar2
DEVOURER_BW=40receive path. The #352 body reports ad-hoc runs with an 8822BU receiver reading zero at both primary-channel offsets. Jaguar2 TX at 40 MHz is validated bytests/jaguar2_tx_bw40.shagainst a kernel sniffer; the devourer receive side at 40 MHz has no record.docs/vht-on-2g4.mdno longer claims it is dead, only that it is unmeasured. - 80 MHz on Jaguar1 and Jaguar2, both directions, with the same control structure (a 20 MHz control per leg, the wide monitor shown hearing a narrow frame before it is asked to hear a wide one).
- 2.4 GHz channels other than 6, including the grid-edge fits from #500 (ch1 HT40−, ch13 HT40+ were measured as transmitter only), and at least one 5 GHz channel at 40 MHz on the RX side.
How
tests/bw40_pair_onair.sh already takes --dut, --peer, --channel and --offset, so the first three items are runs, not code — except that the script has no 80 MHz cells yet (DEVOURER_BW=80 / DEVOURER_HOP_BW=80 and the /80 rates would need adding). Keep each leg's 20 MHz control and the peer power sweep (--peer-tx-pwr): on the same-host pair, peer MCS7 into the 8812AU read 0 % at the Kestrel's 20 dBm default and 90 % at 12 or 4 dBm, so a dense-constellation zero must be checked for near-field saturation before it is read as a width defect.
🤖 Generated with Claude Code
- Dominant language
- C
- Stars
- 56
- Forks
- 29
- Avg merge
- 3h 43m
- Merged PRs (30d)
- 75
Getting set up
This project ships no dev container, Dockerfile or contributing guide, so setting up is up to you: start from its README, and see our first-contribution guide for the general steps.
First steps
- Read the whole issue, then the project's contributing guide.
- Comment on the issue to say you are picking it up — it saves two people doing the same work.
- Fork the repository and make your change on a branch.
- Open a pull request that references the issue number.
More from OpenIPC/devourer
-
Difficulty 2/5 1-3 hours Newbie friendliness 82/100
Maintainers usually reply within 1 day
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Possibly taken @josephnef claimed this today. Openenhancement
Difficulty 4/5 3-5 days Newbie friendliness 42/100
Maintainers usually reply within 1 day
-
Difficulty 5/5 Over a week Newbie friendliness 12/100
OpenIPC/devourer#579 · 1 comment ·
Maintainers usually reply within 1 day
-
enhancement
Difficulty 5/5 Over a week Newbie friendliness 12/100
Maintainers usually reply within 1 day
-
enhancement
Difficulty 5/5 Over a week Newbie friendliness 8/100
Maintainers usually reply within 1 day
All issues in OpenIPC/devourer
Similar issues
-
needs triage
Difficulty 2/5 1-3 hours Newbie friendliness 70/100
389ds/389-ds-base#8157 ·
Maintainers usually reply within 2 days
-
Difficulty 2/5 1-3 hours Newbie friendliness 67/100
coolsnowwolf/lede#14305 ·
Maintainers usually reply within 1 day
-
bug
Difficulty 2/5 1-3 hours Newbie friendliness 84/100
Maintainers usually reply within 1 day
-
Difficulty 2/5 1-3 hours Newbie friendliness 72/100
Maintainers usually reply within 1 day
-
Needs-Triage
Difficulty 2/5 1-3 hours Newbie friendliness 66/100
Maintainers usually reply within 2 days