40 MHz / 80 MHz coverage left open by #352: 8814AU, 8821AU, Jaguar2 RX, 80 MHz, other channels
维护者通常 1 天内回复
还没有人认领这个 Issue。
评估
- 难度
- 4/5
- 预计耗时
- 3-5 天
- 新手友好度
- 34/100
- Issue 类型
- 功能
- 描述清晰度
- 基本清楚
- 活跃度
- 活跃
- 技术栈
- c
- 领域
- networking, testing
调研方向
Start with tests/bw40_pair_onair.sh and docs/vht-on-2g4.md, then review the existing Jaguar2 40 MHz transmit test and the rtw_get_center_ch handling referenced in the issue. The issue calls for measurements across additional chips, receive paths, bandwidths and channels; 80 MHz coverage also needs new cells and rates. Done means recording those measurements with per-leg 20 MHz controls and peer power sweeps.
由索引模型根据 Issue 内容生成。
描述
What is left unmeasured after #352
#352 (Jaguar1 40 MHz dead both ways) closed on 2026-11-09: the cause was the HT40 centre-channel tune fixed in #500, verified on an RTL8812AU against an RTL8852CU with tests/bw40_pair_onair.sh (branch bw40-352-verify). That verification covered exactly one die, one channel and one width. These cells are still open:
- RTL8814AU and RTL8821AU at 40 MHz. Both go through the same
rtw_get_center_chrule as the 8812AU but neither has been measured (noted as unverified in #500 as well). The 8814AU needs the pinned-kernel VM for any vendor-driver control and is judged by its devourer-TX cells only. - Jaguar2
DEVOURER_BW=40receive path. The #352 body reports ad-hoc runs with an 8822BU receiver reading zero at both primary-channel offsets. Jaguar2 TX at 40 MHz is validated bytests/jaguar2_tx_bw40.shagainst a kernel sniffer; the devourer receive side at 40 MHz has no record.docs/vht-on-2g4.mdno longer claims it is dead, only that it is unmeasured. - 80 MHz on Jaguar1 and Jaguar2, both directions, with the same control structure (a 20 MHz control per leg, the wide monitor shown hearing a narrow frame before it is asked to hear a wide one).
- 2.4 GHz channels other than 6, including the grid-edge fits from #500 (ch1 HT40−, ch13 HT40+ were measured as transmitter only), and at least one 5 GHz channel at 40 MHz on the RX side.
How
tests/bw40_pair_onair.sh already takes --dut, --peer, --channel and --offset, so the first three items are runs, not code — except that the script has no 80 MHz cells yet (DEVOURER_BW=80 / DEVOURER_HOP_BW=80 and the /80 rates would need adding). Keep each leg's 20 MHz control and the peer power sweep (--peer-tx-pwr): on the same-host pair, peer MCS7 into the 8812AU read 0 % at the Kestrel's 20 dBm default and 90 % at 12 or 4 dBm, so a dense-constellation zero must be checked for near-field saturation before it is read as a width defect.
🤖 Generated with Claude Code
- 主要语言
- C
- 星标
- 56
- 派生
- 29
- 平均合并
- 3 小时 43 分钟
- 30 天内合并 PR
- 75
环境准备
这个项目没有提供开发容器、Dockerfile 或贡献指南,环境需要你自己搭建:先看它的 README,通用步骤见我们的新手贡献指南。
从这里开始
- 先读完整个 Issue,再读项目的贡献指南。
- 在 Issue 下留言说明你要接手 —— 这能避免两个人做同样的事。
- Fork 仓库,在一个分支上完成修改。
- 提交 Pull Request,并在描述里引用这个 Issue 编号。
OpenIPC/devourer 的其他 Issue
-
难度 2/5 1-3 小时 新手友好度 82/100
维护者通常 1 天内回复
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)可能已有人在做 @josephnef 今天认领。 未关闭enhancement
难度 4/5 3-5 天 新手友好度 42/100
维护者通常 1 天内回复
-
难度 5/5 一周以上 新手友好度 12/100
OpenIPC/devourer#579 · 1 条评论 ·
维护者通常 1 天内回复
-
enhancement
难度 5/5 一周以上 新手友好度 12/100
维护者通常 1 天内回复
-
enhancement
难度 5/5 一周以上 新手友好度 8/100
维护者通常 1 天内回复
相似的 Issue
-
needs triage
难度 2/5 1-3 小时 新手友好度 70/100
389ds/389-ds-base#8157 ·
维护者通常 2 天内回复
-
难度 2/5 1-3 小时 新手友好度 67/100
coolsnowwolf/lede#14305 ·
维护者通常 1 天内回复
-
bug
难度 2/5 1-3 小时 新手友好度 84/100
维护者通常 1 天内回复
-
难度 2/5 1-3 小时 新手友好度 72/100
维护者通常 1 天内回复
-
Needs-Triage
难度 2/5 1-3 小时 新手友好度 66/100
维护者通常 2 天内回复