40 MHz / 80 MHz coverage left open by #352: 8814AU, 8821AU, Jaguar2 RX, 80 MHz, other channels

Abierto
#554 0 comentarios 0 reacciones 0 asignados Ver en GitHub

Los mantenedores suelen responder en 1 día

Nadie ha tomado este issue todavía.

Evaluación

Dificultad
4/5
Tiempo estimado
3-5 días
Aptitud para principiantes
34/100
Tipo de issue
Nueva funcionalidad
Claridad
Bastante claro
Estado de actividad
Activo
Stack tecnológico
c

Línea de trabajo

Start with tests/bw40_pair_onair.sh and docs/vht-on-2g4.md, then review the existing Jaguar2 40 MHz transmit test and the rtw_get_center_ch handling referenced in the issue. The issue calls for measurements across additional chips, receive paths, bandwidths and channels; 80 MHz coverage also needs new cells and rates. Done means recording those measurements with per-leg 20 MHz controls and peer power sweeps.

Escrito por el modelo de indexación a partir del texto del issue.

Descripción

enhancement

What is left unmeasured after #352

#352 (Jaguar1 40 MHz dead both ways) closed on 2026-11-09: the cause was the HT40 centre-channel tune fixed in #500, verified on an RTL8812AU against an RTL8852CU with tests/bw40_pair_onair.sh (branch bw40-352-verify). That verification covered exactly one die, one channel and one width. These cells are still open:

  • RTL8814AU and RTL8821AU at 40 MHz. Both go through the same rtw_get_center_ch rule as the 8812AU but neither has been measured (noted as unverified in #500 as well). The 8814AU needs the pinned-kernel VM for any vendor-driver control and is judged by its devourer-TX cells only.
  • Jaguar2 DEVOURER_BW=40 receive path. The #352 body reports ad-hoc runs with an 8822BU receiver reading zero at both primary-channel offsets. Jaguar2 TX at 40 MHz is validated by tests/jaguar2_tx_bw40.sh against a kernel sniffer; the devourer receive side at 40 MHz has no record. docs/vht-on-2g4.md no longer claims it is dead, only that it is unmeasured.
  • 80 MHz on Jaguar1 and Jaguar2, both directions, with the same control structure (a 20 MHz control per leg, the wide monitor shown hearing a narrow frame before it is asked to hear a wide one).
  • 2.4 GHz channels other than 6, including the grid-edge fits from #500 (ch1 HT40−, ch13 HT40+ were measured as transmitter only), and at least one 5 GHz channel at 40 MHz on the RX side.

How

tests/bw40_pair_onair.sh already takes --dut, --peer, --channel and --offset, so the first three items are runs, not code — except that the script has no 80 MHz cells yet (DEVOURER_BW=80 / DEVOURER_HOP_BW=80 and the /80 rates would need adding). Keep each leg's 20 MHz control and the peer power sweep (--peer-tx-pwr): on the same-host pair, peer MCS7 into the 8812AU read 0 % at the Kestrel's 20 dBm default and 90 % at 12 or 4 dBm, so a dense-constellation zero must be checked for near-field saturation before it is read as a width defect.

🤖 Generated with Claude Code

Lenguaje dominante
C
Estrellas
56
Forks
29
Merge medio
3 h 43 min
PR fusionados (30 d)
75

Preparar el entorno

Este proyecto no incluye contenedor de desarrollo, Dockerfile ni guía de contribución, así que la configuración corre por tu cuenta: empieza por su README y consulta nuestra guía para la primera contribución para los pasos generales.

Primeros pasos

  1. Lee el issue completo y luego la guía de contribución del proyecto.
  2. Comenta en el issue que vas a ocuparte — evita que dos personas hagan lo mismo.
  3. Haz un fork del repositorio y trabaja en una rama.
  4. Abre un pull request que haga referencia al número del issue.

Más de OpenIPC/devourer

Todos los issues de OpenIPC/devourer

Issues similares

Más issues de C

Recibe los nuevos issues en tu correo

Un resumen breve de issues de GitHub para principiantes.