Owner

CU-Robotics

已索引 1 個儲存庫 · 在 GitHub 檢視

正在載入 Issue

可能已有人在做的 issue 排在最後。 全部依時間排序

  • Estimate chassis roll and pitch and send them to hive (auto-aim misses on slopes)
    未關閉
    not started

    難度 5/5 一週以上 新手友好度 35/100

    CU-Robotics/firmware#258 ·

  • Add unit tests for SafetyState
    未關閉
    good first issue not started

    難度 2/5 1-3 小時 新手友好度 90/100

    CU-Robotics/firmware#257 ·

  • Report watchdog restarts and which loop step stalled
    未關閉
    good first issue not started

    難度 3/5 1-2 天 新手友好度 76/100

    CU-Robotics/firmware#256 ·

  • remove hardware dependencies in controls/
    未關閉
    in progress software-in-the-loop

    難度 4/5 3-5 天 新手友好度 42/100

    CU-Robotics/firmware#250 · 1 則留言 ·

  • split gimbal and chassis estimators
    未關閉
    not started software-in-the-loop

    難度 4/5 3-5 天 新手友好度 42/100

    CU-Robotics/firmware#249 ·

  • IMU Recalibration from switch
    可能重新可做 @kylanlints 於 37 天前認領,目前沒有進行中的 PR。 未關閉
    in progress

    CU-Robotics/firmware#244 · 已指派 1 人 ·

  • investigate making robot stop faster on stick release
    未關閉
    not started

    難度 4/5 3-5 天 新手友好度 25/100

    CU-Robotics/firmware#243 ·

  • 72/36 config packets loaded
    未關閉
    not started

    難度 3/5 1-2 天 新手友好度 48/100

    CU-Robotics/firmware#231 · 1 則留言 ·

  • Preserve state across firmware/hive mode
    可能重新可做 @ericv555 於 39 天前認領,目前沒有進行中的 PR。 未關閉

    CU-Robotics/firmware#229 · 已指派 1 人 ·

  • Pre-flight checks
    未關閉
    in progress

    難度 2/5 1-3 小時 新手友好度 70/100

    CU-Robotics/firmware#222 ·

  • Use ref drawing to display the particle filter
    可能重新可做 @leBronzo1 於 76 天前認領,目前沒有進行中的 PR。 未關閉

    CU-Robotics/firmware#219 · 已指派 1 人 ·

  • Fix close range auto aim movement and safety asserts
    未關閉
    not started

    難度 3/5 1-2 天 新手友好度 52/100

    CU-Robotics/firmware#217 ·

  • Integrate VN100 Driver into SensorManager
    未關閉
    in progress

    難度 4/5 3-5 天 新手友好度 38/100

    CU-Robotics/firmware#215 ·

  • Configure from SD Card
    可能重新可做 @kylanlints 於 72 天前認領,目前沒有進行中的 PR。 未關閉
    good first issue in progress

    CU-Robotics/firmware#213 · 已指派 1 人 ·

  • smarter safety asserts
    未關閉
    in progress

    難度 5/5 一週以上 新手友好度 25/100

    CU-Robotics/firmware#211 ·

  • Print expected and received robot id inside the mismatch error
    未關閉

    難度 1/5 1 小時以內 新手友好度 55/100

    CU-Robotics/firmware#172 ·

  • Fix existing clang-tidy findings
    可能已有人在做 @roccoagain 今天認領。 未關閉

    CU-Robotics/firmware#262 · 已指派 1 人 ·

  • Teensy logging to SD card
    可能已有人在做 @nrmayer 於 79 天前認領。 未關閉

    CU-Robotics/firmware#214 · 已指派 1 人 ·

  • RGB robot status lights
    可能已有人在做 @drf821 於 6 天前認領。 未關閉
    good first issue in progress

    CU-Robotics/firmware#212 · 已指派 1 人 ·

把新 issue 寄到你的電子郵件信箱

精選適合新手參與的 GitHub issue 摘要。