Chủ sở hữu

Đã lập chỉ mục 1 kho mã nguồn · Xem trên GitHub

Các issue có thể đã có người làm được xếp cuối danh sách. Sắp xếp tất cả theo ngày

  • Estimate chassis roll and pitch and send them to hive (auto-aim misses on slopes)
    Đang mở
    not started

    Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 35/100

    CU-Robotics/firmware#258 ·

  • Add unit tests for SafetyState
    Đang mở
    good first issue not started

    Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 90/100

    CU-Robotics/firmware#257 ·

  • Report watchdog restarts and which loop step stalled
    Đang mở
    good first issue not started

    Độ khó 3/5 1-2 ngày Mức phù hợp với người mới 76/100

    CU-Robotics/firmware#256 ·

  • remove hardware dependencies in controls/
    Đang mở
    in progress software-in-the-loop

    Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 42/100

    CU-Robotics/firmware#250 · 1 bình luận ·

  • split gimbal and chassis estimators
    Đang mở
    not started software-in-the-loop

    Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 42/100

    CU-Robotics/firmware#249 ·

  • IMU Recalibration from switch
    Có thể làm lại được @kylanlints đã nhận 37 ngày trước và không có pull request nào đang mở. Đang mở
    in progress

    CU-Robotics/firmware#244 · 1 người được giao ·

  • investigate making robot stop faster on stick release
    Đang mở
    not started

    Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 25/100

    CU-Robotics/firmware#243 ·

  • 72/36 config packets loaded
    Đang mở
    not started

    Độ khó 3/5 1-2 ngày Mức phù hợp với người mới 48/100

    CU-Robotics/firmware#231 · 1 bình luận ·

  • Preserve state across firmware/hive mode
    Có thể làm lại được @ericv555 đã nhận 39 ngày trước và không có pull request nào đang mở. Đang mở

    CU-Robotics/firmware#229 · 1 người được giao ·

  • Pre-flight checks
    Đang mở
    in progress

    Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 70/100

    CU-Robotics/firmware#222 ·

  • Use ref drawing to display the particle filter
    Có thể làm lại được @leBronzo1 đã nhận 76 ngày trước và không có pull request nào đang mở. Đang mở

    CU-Robotics/firmware#219 · 1 người được giao ·

  • Fix close range auto aim movement and safety asserts
    Đang mở
    not started

    Độ khó 3/5 1-2 ngày Mức phù hợp với người mới 52/100

    CU-Robotics/firmware#217 ·

  • Integrate VN100 Driver into SensorManager
    Đang mở
    in progress

    Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 38/100

    CU-Robotics/firmware#215 ·

  • Configure from SD Card
    Có thể làm lại được @kylanlints đã nhận 72 ngày trước và không có pull request nào đang mở. Đang mở
    good first issue in progress

    CU-Robotics/firmware#213 · 1 người được giao ·

  • smarter safety asserts
    Đang mở
    in progress

    Độ khó 5/5 Hơn một tuần Mức phù hợp với người mới 25/100

    CU-Robotics/firmware#211 ·

  • Print expected and received robot id inside the mismatch error
    Đang mở

    Độ khó 1/5 Dưới một giờ Mức phù hợp với người mới 55/100

    CU-Robotics/firmware#172 ·

  • Fix existing clang-tidy findings
    Có thể đã có người làm @roccoagain đã nhận hôm nay. Đang mở

    CU-Robotics/firmware#262 · 1 người được giao ·

  • Teensy logging to SD card
    Có thể đã có người làm @nrmayer đã nhận 79 ngày trước. Đang mở

    CU-Robotics/firmware#214 · 1 người được giao ·

  • RGB robot status lights
    Có thể đã có người làm @drf821 đã nhận 6 ngày trước. Đang mở
    good first issue in progress

    CU-Robotics/firmware#212 · 1 người được giao ·

Nhận issue mới trong hộp thư của bạn

Bản tóm tắt ngắn những issue GitHub phù hợp với người mới.