[BUG] ZimaOS v1.6.2: WPA3-SAE is missing from wpa_supplicant, preventing all 6 GHz Wi‑Fi connections

ZimaOSで使用されているBuildroot wpa_supplicant設定から始め、WPA3/SAEオプションがどのように選択されているかを調べます。生成された設定をCONFIG_IEEE80211WおよびCONFIG_SAEと比較します。イメージを再ビルドし、提供されたnmcli WPA3プロファイルを再度試して、journalに無効なkey_mgmt SAE/FT-SAEが報告されなくなったこと、および6 GHz接続が有効になることを確認します。

## Bug summary

ZimaOS v1.6.2 cannot connect to WPA3-Personal Wi‑Fi networks because the bundled `wpa_supplicant` was built without SAE support.

This also prevents connecting to all 6 GHz Wi‑Fi networks, since 6 GHz requires WPA3-Personal/SAE (or Enhanced Open), rather than WPA2-Personal.

The failure is local and occurs before authentication or association with the access point.

## Environment

- Device: ZimaCube
- OS: ZimaOS v1.6.2
- Build date: 2026-07-09
- Architecture: amd64
- Wi‑Fi adapter: MediaTek MT7925 802.11be PCIe (Filogic 360)
- Kernel driver: `mt7925e`
- Network manager: NetworkManager with wpa_supplicant backend
- Router security: WPA3-Personal, AES/CCMP
- Router 6 GHz configuration:
  - SSID: `test6G`
  - Primary channel: 5
  - Frequency: 5975 MHz
  - Width: 160 MHz
  - PSC enabled
  - Wi‑Fi 7 and MLO disabled for troubleshooting

## Expected behavior

ZimaOS should connect to a standard WPA3-Personal 6 GHz SSID using SAE with PMF required.

## Actual behavior

The 6 GHz network is detected correctly, but connection activation fails with:

```text
Error: Connection activation failed: 802.1X supplicant failed

NetworkManager passes the expected WPA3 parameters to wpa_supplicant:

Config added key_mgmt value SAE FT-SAE
Config added ieee80211w value 2

However, the bundled wpa_supplicant rejects both SAE algorithms:

Line 0: invalid key_mgmt 'SAE'
Line 0: invalid key_mgmt 'FT-SAE'
Line 0: no key_mgmt values configured.

NetworkManager then fails the connection:

failure to add network: invalid message format
device (wlan0): state change: config -> failed (reason 'supplicant-failed')
Activation failed for connection test6G

Evidence that radio, driver, AP, and regulatory domain work

The MT7925E adapter successfully detects the 6 GHz access point:

BSS 60:cf:84:3a:90:69(on wlan0)
freq: 5975.0
signal: -58.00 dBm
SSID: test6G

The access point advertises valid 6 GHz operation information:

6 GHz Operation Information:
    Primary Channel: 5
    Channel Width: 80+80 or 160 MHz

The adapter reports 6 GHz support:

GENERAL.DRIVER: mt7925e
WIFI-PROPERTIES.6GHZ: yes

The active regulatory domain is DE, which allows the AP frequency:

country DE: DFS-ETSI
    (5945 - 6425 @ 320), (N/A, 23), (N/A), NO-OUTDOOR

The SSID is on 5975 MHz, therefore it is within the allowed 5945–6425 MHz range.

The same adapter and NetworkManager installation connect successfully to a separate WPA2-Personal 5 GHz SSID. Therefore the issue is specifically the lack of WPA3-SAE support in the shipped supplicant build.

Reproduction steps

1. Use ZimaOS v1.6.2 on ZimaCube with a Wi‑Fi adapter supported by mt7925e.

2. Create or use a WPA3-Personal-only Wi‑Fi network.

3. For a 6 GHz test, configure a legal PSC channel, for example channel 5 / 5975 MHz.

4. Scan successfully:

   sudo nmcli device wifi rescan ifname wlan0
   nmcli device wifi list ifname wlan0
   

5. Create a WPA3-SAE profile:

   sudo nmcli connection add \
     type wifi \
     ifname wlan0 \
     con-name 'test6G' \
     ssid 'test6G'
   
   sudo nmcli connection modify 'test6G' \
     802-11-wireless.mode infrastructure \
     802-11-wireless.band a \
     802-11-wireless-security.key-mgmt sae \
     802-11-wireless-security.pmf 3 \
     ipv4.method auto \
     ipv6.method auto
   

6. Add a valid password and activate the profile:

   sudo nmcli connection modify 'test6G' \
     802-11-wireless-security.psk 'REDACTED'
   
   sudo nmcli connection up 'test6G' ifname wlan0
   

7. Observe the invalid key_mgmt SAE and invalid key_mgmt FT-SAE errors in the journal.

Requested fix

Please enable WPA3 support in the Buildroot wpa_supplicant configuration used for ZimaOS.

At minimum, the wpa_supplicant build must include:

CONFIG_IEEE80211W=y
CONFIG_SAE=y

Please also enable FT-SAE support where appropriate.

Buildroot provides a WPA3 support option for wpa_supplicant, and CONFIG_SAE=y is the required compile-time option for WPA3-Personal/SAE. Without it, NetworkManager cannot activate any WPA3-Personal connection and ZimaOS cannot use 6 GHz Wi‑Fi.

Impact

This affects:

• Any WPA3-Personal-only network
• Every standard secured 6 GHz Wi‑Fi network
• Wi‑Fi 6E and Wi‑Fi 7 client use cases on ZimaOS
• Modern routers configured securely without WPA2 fallback

Additional notes

• iwd is not installed in the ZimaOS v1.6.2 image, so there is no alternative wireless backend available as a workaround.
• The issue is not caused by the regulatory domain, channel width, router signal, or MT7925E driver.
• A local workaround is to use a separate WPA2-Personal 5 GHz SSID, but WPA2 cannot be used as a fallback on 6 GHz.