Follow-ups left open by the Jaguar3 wide-TX IGI floor (#484)
Maintainer antworten meist innerhalb von 1 Tag
Dieses Issue hat noch niemand übernommen.
Bewertung
- Schwierigkeit
- 5/5
- Geschätzter Aufwand
- Über eine Woche
- Anfängerfreundlichkeit
- 15/100
- Issue-Typ
- Bug
- Klarheit
- Größtenteils klar
- Aktivitätsstatus
- Aktiv
- Tech-Stack
- c
- Bereich
- networking
Rechercherichtung
Start with the idle-vs-live register diff in docs/experiments/8822c-ht40-tx-stall.md and the wide_tx_igi_floor path that sets 0x35, using DEVOURER_WIDE_TX_IGI_FLOOR=0 as the control. Each bullet is a bench measurement or an open hardware question, so the work needs the Jaguar3 test units. Done means the RX-cost, 0x2e-0x32 bisect, 80 MHz and 2.4 GHz results are recorded in the experiment doc.
Vom Indexierungsmodell aus dem Issue-Text verfasst.
Beschreibung
Open items from #484 (Jaguar3 40/80 MHz inject: wide_tx_igi_floor on both dies, 8822C DISDATAFB on wide frames), none of them blocking the merge:
- The floor's RX-sensitivity cost is an estimate. The default 0x35 is 21 IGI steps over the DFS floor and 19-23 over the non-DFS window, quoted as "~1 dB per step" and never measured. This is the number an FPV uplink actually pays on the wide-transmitting side. Measure it: same transmitter at a fixed attenuation into a wide-TX session with the floor at 0x35 vs
DEVOURER_WIDE_TX_IGI_FLOOR=0(RX-only arming never happens, so the control is a session that sends one wide frame then listens), delivery vs attenuation, both dies. - No margin story behind the default. 0x35 is the lowest value that cleared the four units measured, not a margin over a characterized edge: one 8812CU clears at 0x24, the second hangs at 0x26 and airs ~1.5 k frames then wedges at 0x2c, and was never bisected between 0x2c and 0x35. Bisect that unit (0x2e/0x30/0x32, silent 144(-), MCS3/40, the
257 submitted / 8 failed / 0 airedshape as the fail criterion) so the default is "edge + N" rather than "the highest value anyone needed". - The real lever is unidentified. The hold is the receiver parking, on a quiet channel, in a gain state where the secondary 20 MHz never reads idle; any received traffic re-runs the AGC and clears it,
DEVOURER_DIS_CCA(MAC CCA + EDCCA + sec20/40/80 gates) is inert against it, and the vendor phydm has no bandwidth-raised DIG bound (phydm_dig_abs_boundary_decisionpins DFS atDIG_MIN_DFSat every width). The IGI floor is a workaround that buys TX at the cost of RX gain. The idle-vs-live register diff indocs/experiments/8822c-ht40-tx-stall.md(RF 0x08/0x58, CCK/AGC status 0x1a30-0x1a68) is where to look for a state the secondary CCA path reads; a lever that re-arms the AGC without raising IGI would make the floor unnecessary. - 80 MHz only partially validated. CU -> EU on 149(+) at VHT1SS_MCS3/80 with the old 0x26 floor ran 470 / 10 / 209; the 0x35 default has not been flown at 80 MHz on either bench. Re-run on a silent 80 MHz block with the default and with the floor off.
- 2.4 GHz HT40 (ch 6). The CU drained on the TX side but the witness received none of it, before and after the change. Unexplained; not a 5 GHz-only feature claim until it is.
- The 8812EU module's scattered send failures. On the second bench the BL-M8812EU2 drops single sends beside
coex: tick failed (rtw_read: iostream error)in otherwise clean runs (13/8501 on 144(-), 64/7316 on busy 36(+)); the CU on the same hub never does. Not the stall shape, and probably that unit's USB wiring (bare module on a bench supply), but it has not been proven so: swap port / cable once and see whether the errors follow the module.
🤖 Generated with Claude Code
- Vorherrschende Sprache
- C
- Sterne
- 56
- Forks
- 29
- Ø Merge
- 3 Std. 43 Min.
- Gemergte PRs (30 T.)
- 75
Entwicklungsumgebung
Dieses Projekt bietet weder Dev-Container noch Dockerfile noch Beitragsleitfaden – die Einrichtung liegt bei Ihnen. Beginnen Sie mit der README; die allgemeinen Schritte stehen in unserem Leitfaden für den ersten Beitrag.
Erste Schritte
- Lesen Sie das ganze Issue und danach den Beitragsleitfaden des Projekts.
- Schreiben Sie ins Issue, dass Sie es übernehmen — das erspart doppelte Arbeit.
- Forken Sie das Repository und arbeiten Sie in einem Branch.
- Öffnen Sie einen Pull Request, der die Issue-Nummer nennt.
Mehr aus OpenIPC/devourer
-
Schwierigkeit 2/5 1-3 Stunden Anfängerfreundlichkeit 82/100
Maintainer antworten meist innerhalb von 1 Tag
-
Follow-ups left open by the 8822B fast bandwidth toggle fix (#584)Evtl. vergeben @josephnef hat das heute übernommen. Offenenhancement
Schwierigkeit 4/5 3-5 Tage Anfängerfreundlichkeit 42/100
Maintainer antworten meist innerhalb von 1 Tag
-
Schwierigkeit 5/5 Über eine Woche Anfängerfreundlichkeit 12/100
OpenIPC/devourer#579 · 1 Kommentar ·
Maintainer antworten meist innerhalb von 1 Tag
-
enhancement
Schwierigkeit 5/5 Über eine Woche Anfängerfreundlichkeit 12/100
Maintainer antworten meist innerhalb von 1 Tag
-
enhancement
Schwierigkeit 5/5 Über eine Woche Anfängerfreundlichkeit 8/100
Maintainer antworten meist innerhalb von 1 Tag
Alle Issues in OpenIPC/devourer
Ähnliche Issues
-
Schwierigkeit 2/5 1-3 Stunden Anfängerfreundlichkeit 72/100
Maintainer antworten meist innerhalb von 1 Tag
-
Needs-Triage
Schwierigkeit 2/5 1-3 Stunden Anfängerfreundlichkeit 66/100
Maintainer antworten meist innerhalb von 2 Tagen
-
issue: bug report
Schwierigkeit 2/5 1-3 Stunden Anfängerfreundlichkeit 82/100
Maintainer antworten meist innerhalb von 2 Tagen
-
cross-platform fix-now
Schwierigkeit 2/5 1-3 Stunden Anfängerfreundlichkeit 76/100
Maintainer antworten meist innerhalb von 1 Tag
-
feature:index kind:crash status:confirmed triaged
Schwierigkeit 2/5 1-3 Stunden Anfängerfreundlichkeit 77/100
clice-io/clice#1123 · 1 Kommentar ·
Maintainer antworten meist innerhalb von 1 Tag