FT-857D RX frequency increments for satellites with identical RX and TX frequencies
还没有人认领这个 Issue。
评估
- 难度
- 4/5
- 预计耗时
- 3-5 天
- 新手友好度
- 15/100
- Issue 类型
- 缺陷
- 描述清晰度
- 基本清楚
- 活跃度
- 停滞
- 技术栈
- c, linux
- 领域
- desktop-dev
调研方向
The report points to the transponder file ~/.config/Gpredict/trsp/53106.trsp (its DOWN_LOW and UP_LOW values for the same frequency) and the rig file with Type=4, LO and LO_UP, which the rig-control code reads when Engage is pressed. Start in the gpredict source where the rig is updated during tracking, and check how it handles the Hamlib rigctld connection on localhost:4533. Done means downlink and uplink keep their own frequencies after Engage, which needs an FT-857D or a rigctld simulator to verify.
由索引模型根据 Issue 内容生成。
描述
This may be related to #294 . I am trying to use gpredict for greencube. To define both the uplink and downlink frequencies, I added the following section to ~/.config/Gpredict/trsp/53106.trsp:
[Mode U GMSK FULL DUPLEX]
DOWN_LOW=435310000
UP_LOW=435310000
MODE=FSK AX.100 Mode 5
BAUD=1200
I defined a rig for this as "FT817/857/897 (auto)" with PTT Status set to "Read PTT". Its .rig file is as follows:
[Radio]
Host=localhost
Port=4533
LO=0
LO_UP=0
Type=4
PTT=1
SIGNAL_AOS=false
SIGNAL_LOS=false
My problem is when I start tracking the satellite and click "Engage", at first everything is normal; both the Downlink and Uplink radio frequencies get updated regularly:
After about 7-8 seconds, both the Downlink and Uplink radio frequencies get set to the same (Uplink) frequency and my Downlink frequency automatically shifts up. From this point onwards, my Downlink radio frequency tracks the Uplink radio frequency.
Fedora 37, gpredict 2.2.1, hamlib-4.5.4.
- 主要语言
- C
- 星标
- 1.2k
- 派生
- 305
- 平均合并
- 8 小时 48 分钟
- 30 天内合并 PR
- 3
环境准备
- 没有 Dockerfile 或 Docker Compose 文件
- 没有 Pull Request 模板
- 阅读贡献指南
从这里开始
- 先读完整个 Issue，再读项目的贡献指南。
- 在 Issue 下留言说明你要接手 —— 这能避免两个人做同样的事。
- Fork 仓库，在一个分支上完成修改。
- 提交 Pull Request，并在描述里引用这个 Issue 编号。
csete/gpredict 的其他 Issue
-
难度 2/5 1-3 小时 新手友好度 82/100
-
bug
难度 2/5 1-3 小时 新手友好度 76/100
-
难度 2/5 1 小时以内 新手友好度 60/100
-
难度 2/5 1-3 小时 新手友好度 68/100
-
难度 4/5 3-5 天 新手友好度 78/100
相似的 Issue
-
mewencode: base256[] and base128[] are indexed out of bounds by a non-ASCII octet可能已有人在做 @kazu-yamamoto 今天认领。 未关闭
难度 2/5 1-3 小时 新手友好度 78/100
kazu-yamamoto/Mew#276 ·
维护者通常 1 天内回复
-
难度 1/5 1 小时以内 新手友好度 91/100
FujiNetWIFI/fujinet-firmware#2045 ·
维护者通常 1 天内回复
-
难度 2/5 1-3 小时 新手友好度 84/100
维护者通常 1 天内回复
-
[Performance]: Qwen-Image-2.1 CPU-only on i5-10500H (6C AVX2, 32 GB): 512x512 in 7.7 min at 8 steps未关闭
难度 1/5 1 小时以内 新手友好度 84/100
维护者通常 1 天内回复
-
area:gates area:gfx found-by:critic kind:gate-defect
难度 2/5 1-3 小时 新手友好度 78/100
InauguralSystems/EigenScript#1825 ·
维护者通常 1 天内回复