IPv6 support: discovery and listeners bind IPv4 only

未關閉
#853 0 則留言 0 個 reaction 已指派 0 人 在 GitHub 檢視

維護者通常 6 天內回覆

還沒有人認領這個 Issue。

評估

難度
5/5
預估耗時
一週以上
新手友好度
18/100
Issue 類型
功能
描述清晰度
基本清楚
活躍度
活躍
技術堆疊
rust
領域
networking

研究方向

Start in bin/ethlambda/src/main.rs: run_node builds p2p_socket on 0.0.0.0, and build_swarm listens on /ip4/0.0.0.0 for QUIC/TCP; spawn_discovery hands one UDP socket to ethrex. Read read_ip and Options::validate_ports for ENR and flag handling, plus #825 for the bootnode refusal. Done means IPv6 listeners/discovery (or a documented ethrex dependency), ip6/udp6/tcp6/quic6 read and written, CLI flags validated, and tests covering dual-stack and IPv6-only peers.

由索引模型根據 Issue 內容生成。

描述

Problem

The node binds IPv4 sockets only, so IPv6 works only for outbound connections:

  • Discovery (discv5) is IPv4-only. run_node builds p2p_socket on 0.0.0.0 (bin/ethlambda/src/main.rs) and passes its IP as DiscoverySpawnConfig::bind_ip. spawn_discovery opens one UdpSocket there and hands it to ethrex's DiscoveryServer. An IPv4 socket cannot send to an IPv6 address or receive from one, so discv5 never reaches an IPv6-only peer, whether it was found by discovery or given as a bootnode.
  • The swarm listens on IPv4 only. build_swarm listens on /ip4/0.0.0.0 for QUIC and TCP, so no peer can connect in over IPv6. Outbound dials to IPv6 do work: libp2p-quic opens a [::]:0 dialer endpoint when no IPv6 listener exists, and TCP opens a socket of the target's family.
  • --discovery.advertise-ip accepts an IPv6 address. It writes ip6 into the ENR, but the sockets behind the record are IPv4, so the published record is one no peer can reach.
  • ENRs from peers. read_ip prefers ip over ip6, and the IPv6-specific ports (udp6, tcp6, quic6) are never read or written.

Today this matters only for IPv6-only peers. A dual-stack record carries ip, which wins.

What support would take

Lighthouse runs dual-stack: --listen-address can be given once per family, the IPv6 ports have their own flags (--port6, --discovery-port6, --quic-port6), and discv5 gets one socket per family. Covering that here means:

  1. Discovery on IPv6 too. ethrex's DiscoveryServer takes a single socket, so this needs either a dual-stack socket with IPv4-mapped addresses handled throughout, or ethrex accepting a second socket.
  2. QUIC and TCP listeners on :: as well as 0.0.0.0.
  3. The ENR's ip6/udp6/tcp6/quic6 entries, written for our record and read from peers'.
  4. CLI flags for the IPv6 listen address and ports, and Options::validate_ports rules for them.
  5. Refusing an IPv6 --discovery.advertise-ip until the above exists, or warning that the record is unreachable.

Related

#825 (open) makes beacon --bootnodes refuse an IPv6 entry that is only a discv5 contact (a bare /ip6/.../udp/<port> multiaddr, or an ENR whose only address is ip6 and whose only port is udp) when discovery is bound to IPv4. The caller passes in the bind address, so the refusal lifts on its own once discovery binds IPv6.

主要語言
Rust
星號
86
分支
34
平均合併
9 天 20 小時
30 天內合併 PR
77

環境準備

從這裡開始

  1. 先讀完整個 Issue,再讀專案的貢獻指南。
  2. 在 Issue 下留言說明你要接手 —— 這能避免兩個人做同樣的事。
  3. Fork 儲存庫,在一個分支上完成修改。
  4. 送出 Pull Request,並在描述裡引用這個 Issue 編號。

lambdaclass/ethlambda 的其他 Issue

查看 lambdaclass/ethlambda 的全部 Issue

相似的 Issue

更多 Rust Issue

把新 issue 寄到你的電子郵件信箱

精選適合新手參與的 GitHub issue 摘要。