Pi Zero W: intermittent loss of approximately 4295 seconds with 6.12 ARMv6 kernels
Maintainer thường phản hồi trong vòng 1 ngày
Chưa có ai nhận issue này.
Đánh giá
- Độ khó
- 5/5
- Thời gian dự kiến
- Hơn một tuần
- Mức phù hợp với người mới
- 35/100
- Loại issue
- Lỗi
- Độ rõ ràng
- Khá rõ ràng
- Mức độ hoạt động
- Sôi nổi
- Công nghệ
- c, linux
- Lĩnh vực
- operating-systems
Hướng nghiên cứu
Start by examining the BCM2835 clocksource and clockevent handling for the 32-bit 1 MHz timer described in the issue. The report does not identify a failing kernel file or provide a deterministic reproduction, so first gather low-overhead diagnostics that distinguish clock accounting errors, clock-set operations, and prolonged stalls. Done means establishing evidence for the source of the roughly 4295-second clock deficit.
Do mô hình lập chỉ mục viết ra từ nội dung của issue.
Mô tả
Describe the bug
Two Raspberry Pi Zero W Rev 1.1 boards running 32-bit Raspbian Bookworm have intermittently fallen behind by about 71 min 35 s during operation. The application detects a large NTP offset and corrects the clock forward. The trigger is unknown.
| Board | Running kernel | Observation |
|---|---|---|
| A | 6.12.96+rpt-rpi-v6 | 2026-09-27: NTPsec recorded +4294.936 s and exited; the journal confirms a subsequent clock correction. |
| A | 6.12.109+rpt-rpi-v6 | 2026-10-13: +4294.035920 s measured and corrected. |
| B | 6.12.96+rpt-rpi-v6 | 2026-10-19: application logged a 4294 s correction; no journal confirmation of the step. |
| A | 6.12.109+rpt-rpi-v6 | 2026-11-17: +4294.844522 s measured; residual after correction −0.011612 s. |
On an earlier incident on board A, two public NTP references and the LAN reference independently agreed that the local clock was behind by about 4296 s.
Steps to reproduce the behaviour
No deterministic reproduction. The boards run headless, with Wi-Fi and Bluetooth active, and an application periodically comparing the local clock against NTP. Expected: the clock advances correctly during unattended operation. Observed: a sporadic large deficit, subsequently corrected forward. No stock-image or kernel-only A/B test has been performed.
Device (s)
Raspberry Pi Zero W / WH
System
Raspberry Pi Zero W Rev 1.1; Raspbian GNU/Linux 12 (Bookworm), armv6l.
Board A on 2026-11-17: 6.12.109+rpt-rpi-v6, package 1:6.12.109-1+rpt1 (build 2026-09-11); boot firmware 2026-09-14 (a86983925695); get_throttled=0x0. The refreshed Bookworm ARMv6 candidate 1:6.12.115-1+rpt1 has not yet been tested in this setup.
All four comparison boards reported active clocksource timer, mask 0xffffffff, and a 32-bit 1 MHz timer in the boot journal. All loaded the same BCM43430 WLAN firmware (7.45.98, FWID 01-8e14b897) and used NTPsec 1.2.2.
Logs
2026-11-17, monotonic journal timeline (seconds since boot):
- 313440.978: locally generated Wi-Fi disconnection; connection to a different AP 0.567 s later. DHCP renewed the same IPv4 address about 1.0 s after the disconnection.
- 313613.414: NTPsec stopped normally for the application-initiated correction, about 172 s after disconnection. No panic exit in this window.
- 313619.298: Tailscale detected the forward clock step during correction; this is not evidence of suspend.
- 313620.930: NTPsec started again.
- 313621.682: correction verified at 08:04:45 CET, applied correction +4294.844522 s, residual −0.011612 s.
About 45 minutes after correction two public NTP sources reported offsets below 2 ms. The latest large offset itself was measured against the LAN reference. The October journal also showed a nearby Wi-Fi reassociation but does not establish a causal link. No matching kernel error was found in the available journal.
Additional context
Two comparable Zero W Rev 1.1 boards still running 6.1.21+ with older boot firmware have no known matching incidents. Kernel, boot firmware and some user-space packages changed together, so this is an association, not an isolated kernel regression.
A full 32-bit timer period at 1 MHz is 4294.967296 s. The latest correction was about 0.123 s smaller. Could this signature indicate lost time in BCM2835 clocksource or clockevent handling? What low-overhead diagnostics would help distinguish a clock accounting error, an unexpected clock-set operation, and a prolonged stall?
A historical FreeBSD report gives a similar offset but does not establish a Linux cause: https://lists.freebsd.org/pipermail/freebsd-arm/2012-December/004443.html
- Ngôn ngữ chính
- C
- Star
- 13.3k
- Fork
- 5.5k
- Merge trung bình
- 4 ngày 10 giờ
- Pull request đã merge (30 ngày)
- 31
Chuẩn bị môi trường
Dự án này không cung cấp dev container, Dockerfile hay hướng dẫn đóng góp, nên bạn cần tự thiết lập môi trường: hãy bắt đầu từ README và xem hướng dẫn đóng góp lần đầu của chúng tôi để biết các bước chung.
Bắt đầu từ đâu
- Đọc hết issue, rồi đọc hướng dẫn đóng góp của dự án.
- Bình luận trên issue rằng bạn sẽ nhận — tránh hai người làm cùng một việc.
- Fork repository và làm thay đổi trên một nhánh.
- Mở pull request có tham chiếu số hiệu của issue.
Issue khác của raspberrypi/linux
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 68/100
raspberrypi/linux#7415 · 2 bình luận · 1 reaction ·
Maintainer thường phản hồi trong vòng 1 ngày
-
rp1-cfe doesn't forward V4L2_EVENT_SOURCE_CHANGE event from csi-2 sensor driver to userspace appĐang mở
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 72/100
raspberrypi/linux#7399 · 1 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày
-
Documentation update requiredĐang mở
Độ khó 1/5 Dưới một giờ Mức phù hợp với người mới 82/100
raspberrypi/linux#7357 · 1 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 68/100
raspberrypi/linux#7054 · 2 bình luận ·
Maintainer thường phản hồi trong vòng 1 ngày
-
Độ khó 4/5 3-5 ngày Mức phù hợp với người mới 48/100
raspberrypi/linux#7770 ·
Maintainer thường phản hồi trong vòng 1 ngày
Tất cả issue của raspberrypi/linux
Issue tương tự
-
Độ khó 1/5 Dưới một giờ Mức phù hợp với người mới 82/100
LedgerHQ/app-bitcoin-legacy#306 ·
-
[issue]: Ventoy2Disk.sh can leave the end of VTOYEFI unwritten (xzcat | dd without iflag=fullblock)Đang mở
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 78/100
-
bug
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 73/100
prusa3d/Prusa-Firmware-Buddy#5629 ·
-
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 84/100
Maintainer thường phản hồi trong vòng 3 ngày
-
Issue PRL on WindowsĐang mở
Độ khó 2/5 1-3 giờ Mức phù hợp với người mới 78/100
Maintainer thường phản hồi trong vòng 1 ngày