Add network isolation support

Đang mở
#304 2 bình luận 0 reaction 0 người được giao Xem trên GitHub

Maintainer thường phản hồi trong vòng 2 ngày

@jeckersb đang làm issue này rồi.

Từ ngày 8/8/2026.

  • #311 của @jeckersb — đang mở

Đánh giá

Độ khó
5/5
Thời gian dự kiến
Hơn một tuần
Mức phù hợp với người mới
25/100
Loại issue
Tính năng
Độ rõ ràng
Khá rõ ràng
Mức độ hoạt động
Đình trệ
Công nghệ
rust
Lĩnh vực
infrastructure, networking

Hướng nghiên cứu

Start by reading the bcvk VM provisioning and networking code, especially the libvirt integration and the existing bcvk libvirt ssh path; the issue does not name specific files or tests. Determine how to block guest outbound access while preserving host-to-VM connectivity, and account for how staged resources could later be exposed. Done means the VM cannot reach arbitrary internet services while host SSH access still works; linked pull request #311 is already open.

Do mô hình lập chỉ mục viết ra từ nội dung của issue.

Mô tả

(This issue is meant to describe the problem, sketch out requirements, and propose one or more solution(s) in order to be fed into a LLM for initial implementation)

Currently bootc tmt integration tests run inside of a bcvk-provisioned VM. However, this VM has general network access to the outside world. That means the test environment can pull arbitrary data at execution time. We are currently trying to reduce the number of testing flakes in bootc CI. A common source of error is the tests pulling container images from quay.io from inside of the VM. This is problematic because it may be many hours into a CI run before a given test is run and encounters a flake, which invalidates the hours of testing that happened beforehand. It should be noted that although quay.io flakes are the most common, there are other flakes both known and unknown that can also occur from within network-enabled test runners.

The general idea then is to enable support in bcvk to disable as much network as possible. Probably it is sufficient to disable outbound routing from the VM, but other options such as manipulating firewall rules could be considered as well. Care must be taken to ensure connectivity between the host and VM is preserved; for example it should still be possible to bcvk libvirt ssh into the VM from the host, but once inside the VM it should not be possible to connect to arbitrary services on the internet.

A followup to this is to pre-stage any required resources on the test runner host (container images, packages, etc.) and expose those resources into the VM. The network isolation support implementation should take into consideration how those resources are exposed to the VM. I suspect that will likely be handled directly on the filesystem via virtiofs, but it could also be feasible to expose network resources from the host onto the VM. As an example, maybe container images are pulled into the host containers-storage, and then the host re-exports those to the VM via a container registry which is reachable via the local network.

This would make the test execution environment more hermetic and similar to something like mock where the inputs (source, spec, buildroot) are populated at the beginning, and then once the build executes it does not have network access.

This a forcing function to make sure all testing inputs are accounted for beforehand. It should greatly cut down on the number of network failures that happen deep into CI runs. If all needed resources are collected at the beginning of the CI pipeline, this means that any flakes or outages in dependent services will be encountered early and should hopefully cause the pipeline to fail on the order of minutes, instead of hours. It also gives us a common place to implement retry logic in order to tolerate transient network errors.

Ngôn ngữ chính
Rust
Star
142
Fork
40
Merge trung bình
2 ngày 22 giờ
Pull request đã merge (30 ngày)
10

Chuẩn bị môi trường

Mở trong Codespaces

Khởi chạy dev container của dự án ngay trên trình duyệt, bằng tài khoản GitHub của bạn.

  • Không có Dockerfile hay tệp Docker Compose
  • Không có mẫu pull request
  • Không có hướng dẫn đóng góp

Bắt đầu từ đâu

  1. Đọc hết issue, rồi đọc hướng dẫn đóng góp của dự án.
  2. Bình luận trên issue rằng bạn sẽ nhận — tránh hai người làm cùng một việc.
  3. Fork repository và làm thay đổi trên một nhánh.
  4. Mở pull request có tham chiếu số hiệu của issue.

Issue khác của bootc-dev/bcvk

Tất cả issue của bootc-dev/bcvk

Issue tương tự

Thêm issue về Rust

Nhận issue mới trong hộp thư của bạn

Bản tóm tắt ngắn những issue GitHub phù hợp với người mới.