Pi 4 brcmfmac AP (2.4 GHz): firmware stops host TX after a client's mDNS burst. Flow control stuck in XOFF until the driver is reloaded
Maintainers usually reply within 1 day
Nobody has claimed this yet.
Assessment
- Difficulty
- 4/5
- Estimated time
- 3-5 days
- Newbie friendliness
- 43/100
- Issue type
- Bug
- Clarity
- Mostly clear
- Activity status
- Active
- Tech stack
- c, linux
- Domain
- networking
Research direction
Start by reading the brcmfmac flow control and transmit paths, then look for existing handling of fc_xoff and fc_xon; the issue does not name specific source files or tests. Try to reproduce the stall with the described 2.4 GHz AP and multicast burst, and inspect the debugfs counters. Done means the AP continues transmitting after the burst and the counters recover without reloading the driver.
Written by the indexing model from the issue text.
Description
Describe the bug
A Pi 4B runs a NetworkManager hotspot (AP mode, 2.4 GHz, band bg, channel auto → 6, IPv4 shared). When a Windows 11 client joins, data flows for about 2 s, and then the Pi stops sending data to the client. Beacons continue. The driver's debugfs counters show the firmware turned host TX off and never turned it back on:
- fc_xoff > fc_xon
- f2txdata stops increasing
After that, reconnects fail at the 4-way handshake. Later the AP stops beaconing entirely. Only reloading the driver recovers it (modprobe -r brcmfmac_cyw brcmfmac; modprobe brcmfmac). No firmware trap or "halted" message is logged. The only related kernel messages are brcmf_vif_set_mgmt_ie: vndr ie set error : -52.
Trigger
A tcpdump on wlan0 shows that the stall starts when the client sends a burst of about 900 mDNS multicast packets in about 3 s. The packets are Windows Delivery Optimization re-announcing 76 _dosvc._tcp.local service instances, each about 540 bytes, with 3 probes and 3 announcements over both IPv4 and IPv6. This is a client-side quirk, but it's valid traffic, and it permanently disables the AP.
Test results
| Test | Result |
|---|---|
| Same client, 2.4 GHz, channels 6 and 11, Wi-Fi power saving on or off | stalls every time |
| One run | recovered after a 6 s outage (fc_xon caught up), so the stall looks like a race |
| Same client, same burst, 5 GHz (channel 36) | fc_xoff 4 = fc_xon 4, stable 3+ min |
| Same client, outgoing mDNS blocked on the client | no burst, fc_xoff 0, stable 3+ min |
| Same client after a reboot (no burst) | stable |
| Android phone (about 40 mDNS packets) | fc_xoff 23 = fc_xon 23, stable 3+ min |
| AP isolation enabled | still stalls |
| Firmware 7.45.265 (standard) and 7.45.241 (minimal) | both stall |
| Kernel 6.12.62 and 6.18.50 | both stall |
Steps to reproduce the behaviour
- Start a 2.4 GHz NetworkManager hotspot on the Pi 4.
- Connect a client that sends about 900 multicast packets of about 540 bytes within a few seconds after associating. A long-running Windows 11 PC with Delivery Optimization LAN sharing on does this.
- Watch /sys/kernel/debug/ieee80211/phy*/counters: fc_xoff goes above fc_xon and f2txdata freezes.
Device (s)
Raspberry Pi 4 Mod. B
System
- Raspberry Pi OS Trixie (image 2025-12-04), full-upgraded 2026-10-27
- Kernel 6.18.50 (also seen on 6.12.62)
- firmware-brcm80211 20260519
- Firmware: BCM4345/6 7.45.265 (28bca26 CY) FWID 01-b677b91b; also 7.45.241 (minimal)
- wpasupplicant 2.10-24+rpt3, NetworkManager AP mode
Logs
Additional context
Possible related to #7092
- Dominant language
- C
- Stars
- 13.3k
- Forks
- 5.5k
- Avg merge
- 4d 10h
- Merged PRs (30d)
- 31
Getting set up
This project ships no dev container, Dockerfile or contributing guide, so setting up is up to you: start from its README, and see our first-contribution guide for the general steps.
First steps
- Read the whole issue, then the project's contributing guide.
- Comment on the issue to say you are picking it up — it saves two people doing the same work.
- Fork the repository and make your change on a branch.
- Open a pull request that references the issue number.
More from raspberrypi/linux
-
Difficulty 2/5 1-3 hours Newbie friendliness 68/100
raspberrypi/linux#7415 · 2 comments · 1 reaction ·
Maintainers usually reply within 1 day
-
rp1-cfe doesn't forward V4L2_EVENT_SOURCE_CHANGE event from csi-2 sensor driver to userspace appOpen
Difficulty 2/5 1-3 hours Newbie friendliness 72/100
raspberrypi/linux#7399 · 1 comment ·
Maintainers usually reply within 1 day
-
Difficulty 1/5 Under an hour Newbie friendliness 82/100
raspberrypi/linux#7357 · 1 comment ·
Maintainers usually reply within 1 day
-
Difficulty 2/5 1-3 hours Newbie friendliness 68/100
raspberrypi/linux#7054 · 2 comments ·
Maintainers usually reply within 1 day
-
Difficulty 4/5 3-5 days Newbie friendliness 48/100
raspberrypi/linux#7770 ·
Maintainers usually reply within 1 day
All issues in raspberrypi/linux
Similar issues
-
Difficulty 1/5 Under an hour Newbie friendliness 82/100
LedgerHQ/app-bitcoin-legacy#306 ·
-
[issue]: Ventoy2Disk.sh can leave the end of VTOYEFI unwritten (xzcat | dd without iflag=fullblock)Open
Difficulty 2/5 1-3 hours Newbie friendliness 78/100
-
bug
Difficulty 2/5 1-3 hours Newbie friendliness 73/100
prusa3d/Prusa-Firmware-Buddy#5629 ·
-
Difficulty 2/5 1-3 hours Newbie friendliness 84/100
Maintainers usually reply within 3 days
-
Issue PRL on WindowsOpen
Difficulty 2/5 1-3 hours Newbie friendliness 78/100
Maintainers usually reply within 1 day