Performance Issue: FPS does not increase despite lowering/compressing video resolution on Raspberry Pi 5 + IMX296
Nobody has claimed this yet.
Assessment
- Difficulty
- 4/5
- Estimated time
- 3-5 days
- Newbie friendliness
- 42/100
- Issue type
- Bug
- Clarity
- Mostly clear
- Activity status
- Active
- Tech stack
- cpp, raspberry-pi
Research direction
Start by reading the IMX296 sensor driver and its supported sensor modes, then trace how rpicam-vid requests frame rate and image dimensions. Check whether the driver supports cropped sensor readout at the requested 1024×128 size and 240 FPS. Done means identifying whether the requested rate is supported and documenting the relevant configuration or limitation; the issue names no source files or tests.
Written by the indexing model from the issue text.
Description
Description
I am currently building a high-speed camera project using a Raspberry Pi 5 and the Raspberry Pi Global Shutter Camera (IMX296).
My goal is to achieve a higher frame rate (FPS). However, even though I have tried to lower and compress the video resolution using rpicam-vid, the actual FPS remains stagnant and does not increase as expected.
Environment
Hardware: Raspberry Pi 5, Raspberry Pi Global Shutter Camera (IMX296)
OS / Kernel: Raspberry Pi OS (Bookworm)
Software / Tool: rpicam-vid
What I've Tried
I attempted to lower the resolution using the --width and --height arguments in rpicam-vid (for example, dropping it down from the native 1456x1088).
While the output video file size decreases and the resolution changes, the running FPS does not go up. It seems to be capped at the default sensor frame rate.
Question
- Does the IMX296 sensor support windowing/cropping (ROI) or specific sensor modes to achieve higher FPS at lower resolutions on the Raspberry Pi 5?
- Are there specific rpicam-vid arguments (such as --viewfinder-width/--viewfinder-height or explicit --framerate / --level settings) required to properly unlock higher frame rates?
Any guidance or suggestions from the community or the developers would be greatly appreciated!
盧謙毓, 週二 下午5:19
Description
I am currently building a high-speed camera project using a Raspberry Pi 5 and the Raspberry Pi Global Shutter Camera (IMX296).
My goal is to achieve a higher frame rate (FPS). However, even though I have tried to lower and compress the video resolution using rpicam-vid, the actual FPS remains stagnant and does not increase as expected.
Environment
Hardware: Raspberry Pi 5, Raspberry Pi Global Shutter Camera (IMX296)
OS / Kernel: Raspberry Pi OS (Bookworm)
Software / Tool: rpicam-vid
What I've Tried
I attempted to run the following command to record uncompressed high-speed video directly into a ramdisk:
bash
rpicam-vid --frames 480 --framerate 240 --width 1024 --height 128 --codec yuv420 --denoise cdn_off -n -o /mnt/ramdisk/test.yuv
Observed Behavior:
Although the output resolution successfully changes to 1024x128 and the yuv420 file is saved to /mnt/ramdisk/, the actual frame rate does not reach the requested 240 FPS. It seems to be capped at the sensor's standard hardware/driver limit.
Question
- Does the IMX296 sensor driver support a high-speed mode or sensor crop/windowing (ROI) that can unlock higher FPS (like 240 FPS) at lower heights (e.g., 128px) on the Raspberry Pi 5?
- Are there any specific configurations needed in /boot/firmware/config.txt or additional rpicam-vid switches required to achieve this?
Any guidance or suggestions from the community or the developers would be greatly appreciated!
- Dominant language
- C++
- Stars
- 490
- Forks
- 200
- PR merge metrics
- No merged PRs in 30d
Getting set up
This project ships no dev container, Dockerfile or contributing guide, so setting up is up to you: start from its README, and see our first-contribution guide for the general steps.
First steps
- Read the whole issue, then the project's contributing guide.
- Comment on the issue to say you are picking it up — it saves two people doing the same work.
- Fork the repository and make your change on a branch.
- Open a pull request that references the issue number.
More from raspberrypi/libcamera
-
Difficulty 3/5 1-2 days Newbie friendliness 55/100
raspberrypi/libcamera#362 · 2 comments ·
All issues in raspberrypi/libcamera
Similar issues
-
bug
Difficulty 2/5 1-3 hours Newbie friendliness 77/100
distante/esphome-components#50 · 1 comment ·
Maintainers usually reply within 1 day
-
Difficulty 2/5 1-3 hours Newbie friendliness 74/100
-
feat
Difficulty 2/5 1-3 hours Newbie friendliness 65/100
Maintainers usually reply within 1 day
-
Difficulty 2/5 1-3 hours Newbie friendliness 68/100
-
Difficulty 1/5 Under an hour Newbie friendliness 76/100
Maintainers usually reply within 1 day