Implement Controlled Fault Injection for Localization Replay
Los mantenedores suelen responder en 2 días
Nadie ha tomado este issue todavía.
Evaluación
- Dificultad
- 5/5
- Tiempo estimado
- Más de una semana
- Aptitud para principiantes
- 18/100
Línea de trabajo
No files or tests are named in the payload. Start by locating Awkernel's localization replay pipeline and its scenario/configuration entry points, then identify where input streams, timestamps, message delivery, logging, and competing tasks are handled. Done means reproducible fault scenarios with recorded configuration/events, tests checking injected events against their specification, and documented seeds/reproduction commands.
Escrito por el modelo de indexación a partir del texto del issue.
Descripción
Implement reproducible injection of input delays, timestamp offsets, dropped messages, and computational overload into localization replay experiments on Awkernel. Exercise the integrated pipeline under controlled abnormal conditions without modifying the original datasets.
Scope:
- Inject configurable delivery delays and jitter into selected input streams
- Apply timestamp offsets independently of delivery timing
- Drop individual messages or configurable bursts using deterministic rules or seeded randomness
- Introduce controlled computational load through configurable competing tasks
- Support isolated faults and explicitly defined combinations
- Record the injection configuration and actual events observed during each run
Acceptance criteria:
- Each scenario specifies the target stream or task, injection point, start time, duration, and magnitude.
- Delivery-delay injection preserves measurement timestamps unless timestamp modification is explicitly enabled.
- Timestamp-offset injection changes only the configured timestamp fields and documents how per-point times are affected.
- Drop patterns are reproducible, and injected losses are distinguishable from pipeline overflow or processing failures.
- Computational-load scenarios specify workload, CPU affinity, priority, and activation pattern, with actual interference measured.
- Replay continues to offer inputs at the configured rate rather than slowing down to match processing completion.
- Fault-free control runs use the same datasets and baseline configuration.
- Tests verify that injected events match their specification; deviations caused by scheduling are recorded.
- Logs retain original and modified timing information, message identifiers, and injection decisions.
- Scenarios, seeds, configurations, and reproduction commands are documented.
Out of scope:
Defining recovery policies, modifying localization algorithms, physical sensor faults, and vehicle-level safety validation.
- Lenguaje dominante
- Rust
- Estrellas
- 282
- Forks
- 12
- Merge medio
- 2 d 9 h
- PR fusionados (30 d)
- 28
Preparar el entorno
Este proyecto no incluye contenedor de desarrollo, Dockerfile ni guía de contribución, así que la configuración corre por tu cuenta: empieza por su README y consulta nuestra guía para la primera contribución para los pasos generales.
Primeros pasos
- Lee el issue completo y luego la guía de contribución del proyecto.
- Comenta en el issue que vas a ocuparte — evita que dos personas hagan lo mismo.
- Haz un fork del repositorio y trabaja en una rama.
- Abre un pull request que haga referencia al número del issue.
Más de tier4/awkernel
-
Dificultad 1/5 Menos de una hora Aptitud para principiantes 88/100
Los mantenedores suelen responder en 2 días
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 75/100
Los mantenedores suelen responder en 2 días
-
Dificultad 4/5 3-5 días Aptitud para principiantes 48/100
Los mantenedores suelen responder en 2 días
-
Dificultad 4/5 3-5 días Aptitud para principiantes 48/100
Los mantenedores suelen responder en 2 días
-
Deadlock in ixgbeAbierto
Dificultad 4/5 3-5 días Aptitud para principiantes 25/100
Los mantenedores suelen responder en 2 días
Todos los issues de tier4/awkernel
Issues similares
-
marketing
Dificultad 2/5 1-3 horas Aptitud para principiantes 82/100
Los mantenedores suelen responder en 1 día
-
Dificultad 1/5 Menos de una hora Aptitud para principiantes 88/100
flashbots/panetiere#46 · 1 comentario ·
Los mantenedores suelen responder en 5 días
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 78/100
jlcodes99/cockpit-tools#3190 ·
Los mantenedores suelen responder en 4 días
-
Dificultad 2/5 1-3 horas Aptitud para principiantes 72/100
Feyisara2108/stellargive#1376 ·
Los mantenedores suelen responder en 1 día
-
area:post bug effort:medium P7 source:agent
Dificultad 2/5 1-3 horas Aptitud para principiantes 78/100
Los mantenedores suelen responder en 1 día