Vimar 30801 (RemoteControl_v1.0) sends no Zigbee messages on button press

Maintainers usually reply within 1 day

Assessment

Research direction

Description

What happened?

I paired a brand new Vimar Linea View Wireless 30801 ("IoT connected electronic control", dual Bluetooth/Zigbee) with Zigbee2MQTT. It joins the network and is correctly recognized as RemoteControl_v1.0 (exposes only action), but pressing the button never produces any message: no action, no entry in the debug log, and last_seen does not update.

Steps already taken:

• Switched the device to Zigbee mode and installed the Zigbee firmware with the Vimar View Wireless app, then paired it to Z2M.
• Bound endpoint 10 to the Coordinator (genOnOff, genLevelCtrl, closuresWindowCovering): the bind succeeds, still no messages.
• Bound endpoint 10 to a Zigbee bulb (genOnOff): the bind succeeds, but the bulb does not react to the button.

LED behaviour when pressing the button: white flash

According to the official Vimar instruction sheet, if the control is not associated to the Zigbee hub, the LED turns red and the press has no effect. It is configured with the Amazon app for Zigbee, so I suspect it only sends commands to the hub it was associated with, ignoring generic bindings. I could not find any documentation or user report of this device working with a third party coordinator.

What did you expect to happen?

An action (on/off/toggle/...) published on zigbee2mqtt/<friendly_name> each time the button is pressed, as described in the device page for RemoteControl_v1.0.

How to reproduce it (minimal and precise)

1. Put the device in Zigbee mode and pair it with Z2M (permit join).
2. Open the device in the frontend, tab Bind, bind endpoint 10 to the Coordinator.
3. Press the button several times with log_level: debug.
4. Nothing is received.

Zigbee2MQTT version

2.14.2

Adapter firmware version

0x26580700

Adapter

ConBee2/RaspBee2 0x00212effff09cb45

Setup

Home assistant add on. Home assistant VM on ProxMox

Device database.db entry

No response

Debug log

With log_level: debug enabled, pressing the button 5+ times produces no log lines at all for this device (no "Received Zigbee message", no action, no errors). Below are the lines from the successful bind, so it is clear that the device itself is reachable:

[12/11/2026, 00:34:54] z2m: Successfully bound cluster 'genOnOff' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:34:54] z2m: Successfully bound cluster 'genBasic' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:34:54] z2m: Successfully bound cluster 'closuresWindowCovering' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:34:54] z2m: Successfully bound cluster 'genLevelCtrl' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:34:55] z2m: Successfully bound cluster 'genOnOff' from '0xf4ce360119d4cf4b' to 'Luce ufficio'
[12/11/2026, 00:35:00] z2m: Successfully bound cluster 'closuresWindowCovering' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:01] z2m: Successfully bound cluster 'genLevelCtrl' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:01] z2m: Successfully bound cluster 'closuresWindowCovering' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:01] z2m: Successfully bound cluster 'genOnOff' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:01] z2m: Successfully bound cluster 'genLevelCtrl' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:01] z2m: Successfully bound cluster 'genOnOff' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:07] z2m: Successfully bound cluster 'closuresWindowCovering' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:07] z2m: Successfully bound cluster 'genLevelCtrl' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:07] z2m: Successfully bound cluster 'genOnOff' from '0xf4ce360119d4cf4b' to 'Coordinator'
[12/11/2026, 00:35:29] z2m: Successfully bound cluster 'genOnOff' from '0xf4ce360119d4cf4b' to 'Luce ufficio'

Notes

Additional info

• Device model: Vimar 30801, Zigbee model/manufacturer as shown in the Z2M device page: https://www.zigbee2mqtt.io/devices/RemoteControl_v1.0.html
• Clusters tab screenshot attached (output clusters of endpoint 10).
• Has anyone got a View Wireless push button (30801 / 30804) working with Z2M without an Amazon/Vimar hub? Any hint on how it must be configured would be appreciated.
• last_seen and linkquality do not change when the button is pressed, so the device does not appear to transmit anything to the coordinator.
• Reading attributes works: a genBasic read returns {"deviceEnabled":1,"zclVersion":8,"manufacturerName":"Vimar","swBuildId":"1.1.1_z","modelId":"RemoteControl_v1.0"}. So the coordinator can query the device, but button presses never generate any incoming message, even with last_seen enabled and a successful bind.

Getting set up

First steps

1. Read the whole issue, then the project's contributing guide.
2. Comment on the issue to say you are picking it up — it saves two people doing the same work.
3. Fork the repository and make your change on a branch.
4. Open a pull request that references the issue number.

More from Koenkk/zigbee2mqtt

• [Feature request]: OTA for generated definitions of devices with an OTA client cluster

  Possibly taken @jabla claimed this 1 day ago. Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 80/100

  Koenkk/zigbee2mqtt#33684 · 1 comment · Opened Nov 12, 2026

  Maintainers usually reply within 1 day

• [New device support]: 555853 from ENVILAR

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel
  new device support

  Difficulty 2/5 1-3 hours Newbie friendliness 70/100

  Koenkk/zigbee2mqtt#33674 · 1 comment · Opened Nov 11, 2026

  Maintainers usually reply within 1 day

• [Feature request]: Support espzb adapter (ESP Zigbee SDK v2, ESP32-S31)

  Possibly taken A pull request linked to this issue is open or already merged. Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 76/100

  Koenkk/zigbee2mqtt#33668 · Opened Nov 10, 2026

  Maintainers usually reply within 1 day

• Faulty installation instructions

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel
  problem

  Difficulty 1/5 Under an hour Newbie friendliness 76/100

  Koenkk/zigbee2mqtt#33645 · 1 comment · Opened Nov 8, 2026

  Maintainers usually reply within 1 day

• SONOFF MINI-ZB2GS-L: `detach_relay_mode` briefly reported as DISABLE every ~18h, because endpoint 2 reports `detachRelayMode2: 0`

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 83/100

  Koenkk/zigbee2mqtt#33613 · 2 comments · Opened Nov 5, 2026

  Maintainers usually reply within 1 day

All issues in Koenkk/zigbee2mqtt

Similar issues

• Agent snapshot lists a Button rendered as a link with no actions

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 78/100

  vercel-labs/ui#540 · Opened Nov 14, 2026

  Maintainers usually reply within 1 day

• Runners page: ignore -slim suffix when comparing runner and Homer versions

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel
  accepted ai-dev ai-implementing

  Difficulty 2/5 1-3 hours Newbie friendliness 74/100

  livesport/homer#218 · 1 comment · Opened Nov 14, 2026

  Maintainers usually reply within 1 day

• normalizePropName strips `#` characters from Figma property names instead of only the `#id` suffix

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 72/100

  figma/code-connect#419 · Opened Nov 14, 2026

• `dasherize` mangles mid-name and trailing acronyms (`CopyURLElement` throws `SyntaxError`, `@attr URL` -> `data-ur-l`)

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 78/100

  github/catalyst#372 · Opened Nov 14, 2026

• Negative values skip k/M abbreviation and medium decimal format on line, stacked-area, and tooltip

  Open

  ⋯Report a problem with this issue

  • Is something wrong?

  • Already taken
  • Not beginner-friendly
  • Stale or invalid
  • Something else…
  • Send Cancel

  Difficulty 2/5 1-3 hours Newbie friendliness 84/100

  britecharts/britecharts#1255 · Opened Nov 14, 2026

  Maintainers usually reply within 1 day

More TypeScript issues